The first fretted CBG I pressed the frets into the cuts and they mostly held just fine. Over time two fell out and once they did they continue fall out despite firm re-hammering of them.
So I tried just a dot of CA glue (thick) and it oozed on to the fret board which was unsightly.
Is there a specific glue and/or gluing technique I need to use/follow?
Tags:
Most gluing of frets I've seen, including myself, merely use a dab of "super glue" the clear very thin stuff you can buy anywhere from dollar stores to Walmart, not so much in the slot, but on the ends. You tap in your frets, then turn the neck sideways and drip a drop at both ends of the fret, it usually seeps into the slot beneath the fret making contact with the fret and soaking into the wood due to it's thin viscosity.
Soft wood finger/fret boards tend to not be as secure holding the frets as much as a hardwood does, and make sure your making a thin as possible kerf slot for your fret, experiment on a piece of scrap, till you get the slot thickness to feel just right before cutting all of them on your finished gee-tar.
To resolve the issue at hand, you can still try this method, or you may have to remove the offending frets as they come loose, make 50/50 mixture of hardwood sawdust and wood glue, press it into the slot, and immediately tamp the fret back in, excess will squeeze out the sides, wipe, wait to dry, add the superglue to the ends for extra security.
Do not use the gorilla glue products as as these glues dry, they expand, making a mess, possibly even pushing the fret back out.
The very worse case scenario, slots are too loose and you have to let the 50/50 sawdust glue mixture dry before you insert frets, filling in the old slot, and re-cut the slots thinner.
Phil, I have had the same CA experience in the past....more glue outside than in. My solution, after diggin' around in CBN, Stew Mac, etc, was to purchase some "water thin" CA. It's available from many sources. I bought some STARBOND brand EM-O2 in a small kit that included several small "hummingbird beak" nozzles which allow great control over the distribution of the CA. I recall it was @ $10 from Amazon. It is Very Thin! Good CA bond, easy to control and use. Don't squeeze the bottle, just let it flow. Good luck
I have also read many tales of fret gluing on this site, but I have never needed to use glue. I just use a fret saw (stewmac) and hammer them or press them in place. Ive never had them fall out as they usually fit pretty snug in place. But if I did, perhaps I would do it after finishing the neck with tung oil, which may help removing the excess glue.
—Brendan
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray on Tuesday. 11 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans on Sunday. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!