I want to make perfect sound holes.....doesn't everybody?
So what tools specifically do you use.
I have a dremel and bought the router base, but the tool that came with the base does not do a very good job...especially on one of those composite boxes.
I've seen many examples on here of beautiful round holes with no crappy edges.....how do you do it?
If dremel make an attachment for producing perfect holes, what is the part/parts called, and can anyone give me part numbers.
Cigar boxes are too hard to get here in Tasmania, Australia, so I can't really afford to wreck boxes trying out various methods.
Tags:
Hole saw for big round sound holes[1]. Wood bits for smaller. Jigsaw for all the rest.
And - don't forget to put a piece of wood under the soundboard before drilling. It may split otherwise.
[1]I was too lazy to bring my bits from the attic and started with the dremel. That's the only "semi-round" sound hole I have on my CBG... See my pics gallery ;-)
I use milling cutters (normally four or six flute) or slot drills (two flute). They should be super sharp. Keep them turning fast and just rest them on the surface for a moment with very light pressure and let them work their way through the surface. Once they have got past the first half millimetre (which is the dangerous bit) then you can take them in faster. If you need the holes to be good on both sides make sure there is some sacraficial wood behind the piece you are cutting so that it doesn't splinter as it breaks though.
It helps to clamp the work down if you can do that without marking it. If you have fine feed on the drill press, as you have with a milling machine, that will help.
This will give you holes that don't need trims and look smooth. If you are using a wooden box which has a finish on it the edge of the holes will look lighter. Put a little linseed oil (or danish, tung or tru oil) on just to darken it to match the finish of the box.
I use forstner bits for circles. Clean and perfect, even on plywood. I had troubles with tearout when I used paddle bits - even the ones with the corner teeth.
I use forstner bits for circles. Clean and perfect, even on plywood. I had troubles with tearout when I used paddle bits - even the ones with the corner teeth.
I thought you were referring to the ideal size for the best acoustics, I think about the size of a egg is about right.
Cheers Ron
Actually, there was a blistering debate years back on the old Yahoo site about the perfect size for a soundhole. After studying up on the work of physicist Hermann von Helmholtz, the verdict was that for an average cigar box, the optimal size was about that of a quarter. Otherwise you are taking away too much surface which is needed for vibration in order to get the best volume.
However, I don't know if any definitive studies were done. ;->
I use forstner bits for circles. Clean and perfect, even on plywood. I had troubles with tearout when I used paddle bits - even the ones with the corner teeth.
Thanks for that tip, Diane. I guess my sound holes tend to be too small. I will have to try enlarging them and see if that improves sound volume. Too bad I don't have a U.S. quarter handy... A Google search says a U.S. quarter is 31/32nds of an inch in diameter, which is 24.6 mm. Guess that will be close enough.
-Rand.
I only have a small electric hand drill and no drill press- would forstner bits work with this? I read somewhere that they are guided by the outer rim of the bit as opposed to a central point of the bit which makes me think without the drill press it would be hard to get the hole centred and to stop the bit wandering off as the hole is started. Is there a kind of hybrid - forstner plus a drill spike in the centre of the bit for drilling without a drill press?
In the past I have used curtain grommets to make the holes look neater and for my last build and my current one I have gone for f holes slotted with a set of small hand files using f hole templates previously posted by Diane.
David
On my forstner bits, there is a center spike to get you on spot - I usually use an awl to make a divot in the wood for my desired center. The next part of the drill bit that touches the wood is the outer cutting ring, and once that is started into the wood -- that drill isn't going to wander anywhere! Just be sure your drill is as perpendicular as you can get it and go slow and easy. Since it is a ring and not a paddle, there is no jumping about. Much easier to control - and almost no tearout on the back.
Nice F hole!
Started by Bill Andy in Performances, How to Play, Lessons, Concerts 12 hours ago. 0 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Bill Andy 13 hours ago. 5 Replies 0 Likes
Started by BrianQ. in Performances, How to Play, Lessons, Concerts on Tuesday. 0 Replies 2 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!