Replies to This Discussion

Permalink Reply by Paul Craig on January 15, 2021 at 11:42am

Nice pair Michael.

• ▶ Reply

Permalink Reply by t-belly johnson on January 15, 2021 at 12:31pm

• ▶ Reply

Permalink Reply by t-belly johnson on January 15, 2021 at 12:32pm

• ▶ Reply

Permalink Reply by Paul Craig on January 16, 2021 at 12:37pm

When it fails to post, you have to highlight - right click - copy - go to the non post and click edit - right click near the vertical prompt - click paste - then click on add/submit.

Annoying, but after you've posted a couple times it starts working right.

• ▶ Reply

Permalink Reply by BrianQ. on January 16, 2021 at 2:14pm

Just remember this:

• ▶ Reply

Permalink Reply by Paul Craig on January 17, 2021 at 9:47am

Didn't think of that.

• ▶ Reply

Permalink Reply by t-belly johnson on January 16, 2021 at 2:37pm

So... I`ve not bothered making any new guitars for a while. Everyone of my friends, relatives have one!

So in my covid lockdown boredom I decided to have a look at old guitars and sort out the niggly little errors I made early on.

I`m currently working on a 3 stringer, under saddle pickup and EQ pre amp. I`ve removed all the frets and added a radius ( something I did on later models) and will also make the box secure with angle brackets to stop unwanted movement.

Pretty easy work to be honest but I have a few more with errors that I can improve on.

Don`t we all ;) 

ps, thanks Paul and BrianQ

• ▶ Reply

Permalink Reply by Taffy Evans on January 16, 2021 at 7:10pm

Hi, this is another way I have always done it if mistakingly posting incorrectly. When I post I have always gone back into the forum and checked that the new post is there. If it is and it is blank I click on the Edit button, which takes me back to the Reply section, but instead of re-editing I swap to HTML and repost. Then delete the incorrect post.
Taff

• ▶ Reply

Permalink Reply by Paul Craig on January 17, 2021 at 11:20am

I got that SG together, but I had a 1/4" space between the strings and the last fret. The neck pocket(bolt on neck) had a degree cut, but they didn't figure it right. The bridge post were all the way down so I couldn't adjust.

I need a neck shim. I was going to cut my own, but didn't have any suitable wood with the right dimensions. I can't use end grain because it'll split all to pieces in thin sheets. So I ordered a pack of shims from Stewmac. They make them from maple and they're not end grain. They are expensive. Set of 3 for 25 bucks, but you get 3 different degree shims(.25/.5/1degree).

I thought it was going to need the 1 degree shim, but it ended up being the .25 shim and having to raise the bridge 1/8" to get it all correct. Also had to adjust the intonation since the process moved the nut a bit further away from the bridge. Funny how a small change can make so much difference. Anyway, this one is done except for some pickup height adjustments. Loving these pickups.

• ▶ Reply

Permalink Reply by Southern Ray on January 18, 2021 at 7:00am

 Can we hear it, can we hear it?

• ▶ Reply

Permalink Reply by Paul Craig on January 17, 2021 at 11:19am

• ▶ Reply

Permalink Reply by Darryl Tuttle on January 17, 2021 at 1:13pm

• ▶ Reply

• ‹ Previous
• 1
• …
• 158
• 159
• 160
• 161
• 162
• …
• 187
• Next ›
• Page