and I am shopping for some more wood for necks, and pickup up some hardware for some builds. After sorting through the 1x2's, trying to find some that don't have warps or bends, I decide to stop by the power tool department just to see what I can see.
For the longest time, I have wanted to pick up a bench planer, but I just could not justify spending 300 bucks on one, even though the prices have come down on them.
So I am looking at the planers they have, and they are still out of my price range. But then I see a 13 inch Ryobi bench plane. It was marked as originally $229.00, but was marked down to $192.00 on sale. I looked under the benches to see if they had any more of them, but this one appeared to be the last one they had.
I grab Brian from the power tool department, and he confirms that it is the last one of that model. I asked if the $194 was the lowest price on it. He pulled out his scanner and discovered that it was discounted down to $137.00 for the floor model. That sounded a whole lot better to me, so I told him I would take it.
He went to put it in the cart and found that it had been screwed down to the wooden shelf it was sitting on. He went to find a screwdriver, and after a long 15 minutes he finally came back and told me that all the cordless drill/screwdrivers had the batteries run down on them, and nobody had bothered to plug them back in. It would have taken a long time to get the screws out by hand, so I told him he could just put it in the cart, with the pieces of 2x6 it was attached to, and I would just take the wood off when I got home.
He did that and then told me he would take another 10% off the price for me. So when I got to the checkout, the $229.00 planer ended up costing me $124.00!! And including the factory warranty.
He shoots, he scores!!!
So I got it home and set it up on my workbench, I found a piece of scrap to test it out on. Worked like a charm, so I grabbed a few pieces of Ipe fingerboard stock that was rough cut and needed planing. In a matter of seconds, they were smooth and even. It would have taken me hours of sanding to get that hardwood flat like that.
I had never used a planer before, but boy am I a happy camper now!! Under a minute to plan 4 neck blanks smooth.
Yee Haw!!!
Tags:
just think if the Quakers would have been as smart as you!...America would be a differnet place! make them like silly for hand planing all those years....whats bozos!
just kidding good score!
Yea, I hear ya. And I totally understand that some folks are all about hand sanding and using spoke shaves and all those manual ways of woodworking. And, I completely respect and admire their initiative and dedication to building that way.
My problem is that I just don't have the patience to do it that way. If I don't keep moving through a project, I wind up losing interest and don't complete stuff in a timely fashion.
So I use whatever technology is available at a price I can afford.
Cheers!
BeetleJuice! said:
just think if the Quakers would have been as smart as you!...America would be a differnet place! make them like silly for hand planing all those years....whats bozos!
just kidding good score!
Nothing like being in the right place at the right time Dan. I think you are simply reaping some rewards from your good Karmatic actions of the past. Enjoy, Keni Lee
I have to double check, but I think it will shave off down to a 64th of an inch or so.
Keith Duncan said:
Hey dan; great deal i have a question what is the minimum the planer will cut on one pass ??
Started by Bill Andy in Performances, How to Play, Lessons, Concerts 16 hours ago. 0 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Bill Andy 17 hours ago. 5 Replies 0 Likes
Started by BrianQ. in Performances, How to Play, Lessons, Concerts on Tuesday. 0 Replies 2 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!