OK people here it is, the cheapest motorized fret slots cutting aid ever, but I have to give the concept credit to Izzy Swan…
As you can see I took an electric 3/8” drill, used a compressor fitting, male to female to increase the size to 1/2”.
Grinded the little notch off so it would fit in the drill better. The reason why I needed to do this was the blade has a 1/2” hole.
The blade is what is a jeweler slotting blade and I ordered it off EBay:
HSS Jewelers Saw 3" D x .023" W x 1/2" Hole X 230 Teeth Made in Poland, http://www.ebay.com/usr/toolmexonlineoutlet
I really would have liked a 4” blade but the asking prices I found or the shipping costs were ridiculous. I didn’t use sealed bearings as shown on Izzy’s video because I didn’t have any but I did use plastic spacer with 1/2” inside diameter (Lowes) and put a washer on the outside of each one, might have to replace these in the future.
As you can tell the table is pretty rough, scraps I had laying around, wasn’t sure it was going to work, I had to slightly shim the table support to get just the right height of the blade for fret slots. I kept the table away from the drill for 2 reasons, one was to get to the trigger and the other is where the table height is not too high because of the height of the drill.
Cut my first fret board, oak, as you can see.
Tags:
Great idea. I've been eyeing the table saw idea, would like to do something with a small bandsaw too.
I edited your article so the pictures & video were displayed. We're featuring it this week. GREAT IDEA!!!
This is pretty cool, but I find that a coping saw is the simplest easiest way to cut the fret board.
Izzy makes some pretty cool stuff, been following him awhile now. I use the scroll saw to cut fret slots the blade is perfect size, so quick and easy.
I keep the saw on a slow speed, reverse the blade so the teeth face away from me, that way it is easy to see the cut line, and let the blade do the cut with very little pressure use the guide to keep the board square, practice on some scrap you'll find it very easy, don't over tighten the saw blade, it should be about a c note when you give the blade a twang.
Very nice! I've got that blade ordered but I think I'll spring for a $50 mini table saw and just leave it set up for fretting. Thanks for the info!
Awesome Job. Izzy Swan is awesome. ThX for sharing this.
I was gonna add, that I bought the mini table saw from HF it has NO torque. I even had issues cutting scrap pine for fret slots.Oak it would maybe get half or 3/4 of a slot cut and had to finish with a hand saw. I was using the same blade as mentioned above. $5 off ebay. it works well when you have the power behind it. If it had torque it would be an awesome tool for fret slotting for the cost it was. But I had to return it. In the demo video by HF they are cutting balsa wood and Popsicle sticks.
I'll be building one of these since a drill will have the torque to handle this.
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans 2 hours ago. 6 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. 6 hours ago. 4 Replies 0 Likes
Started by BrianQ. in Performances, How to Play, Lessons, Concerts on Tuesday. 0 Replies 2 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!