Replies to This Discussion

Permalink Reply by Wal Callaby on November 29, 2017 at 9:19am

Hi Shane

You guys over there in the US seem to have an inexhaustible supply of poplar for your necks; we in the UK do not. However, I have found an excellent source of oak, iroko and mahogany, pre-rounded at the back, 35mm wide, 20mm deep. Perfect! But what's the best way- no, what's your way of carving out from a hardwood through-neck the bits between the tailpiece and the bridge, and the bridge and the other end of the box. I must have missed that video...

Hoping you can help- Wal

• ▶ Reply

Permalink Reply by Cigar Box Nation on November 29, 2017 at 9:43am

I notch it out using my table saw.  I'd do a video on it, but I'm currently writing a book about building these things and my publisher is asking me to save the big building tips for the book.

• ▶ Reply

Permalink Reply by Wal Callaby on November 29, 2017 at 11:23am

So I could wait for the book... Thing is, i take a rather empirical approach to CBG building, started with no tools at all, and now have one or two. And nowhere to work, not even a bench. When is the book out? Actual paper, or ethereal and web-based? Ah well, at least I can get shaped oak for about a dollar a foot...

• ▶ Reply

Permalink Reply by Cigar Box Nation on November 30, 2017 at 3:59am

Yep, actual book.  One of the biggest woodworking book publishers in the US.  A mix of DIY plans and cigar box guitar history, all from a musician's perspective

• ▶ Reply

Permalink Reply by Kirk on November 30, 2017 at 4:29am

Boss!! Can't wait to buy a copy.

• ▶ Reply

Permalink Reply by JL on November 30, 2017 at 2:44am

I use my bandsaw

• ▶ Reply

Permalink Reply by Dave Lynas on November 29, 2017 at 11:22am

Great tips Shane.

• ▶ Reply

Permalink Reply by JL on November 30, 2017 at 2:55am

Shane,

How do you put the screws into the edge of the sides of the box without them splitting?

• ▶ Reply

Permalink Reply by Cigar Box Nation on November 30, 2017 at 3:58am

very carefully!

• ▶ Reply

Permalink Reply by Paul Craig on November 30, 2017 at 11:53am

Drill pilot holes.

• ▶ Reply

Permalink Reply by Grandpa on December 2, 2017 at 4:32pm

Wal, Glen Watt has several videos on techniques (here on CB Nation, Youtube) to notch out neck blanks to fit inside of the box. Hand saw, chisel, hammer, rasp. More labor, less tool investment. I use a table saw or a band saw, because I have them. There are no steps to building a CBG that cannot be done with hand tools. Power tools make many steps quicker, often more precise, but you can build without them. Better, I think, to start with minimal tools, take your time, and get goin'!  We have seen videos in here where guys make gits using tree limbs, gas/oil cans, and kitchen knives. Then play them. It can be done with what you have.

• ▶ Reply

Permalink Reply by Wal Callaby on December 2, 2017 at 10:44pm

Good points, well made. My first 'real' CBG saw me cut a strip 11" long and just a quarter inch thick lengthwise along an oak neck using just a blunt tenon saw and a sharp eye. Couldn't believe how muck work it was- or how well it turned out. What was cut out is pretty much veneer quality, and it will get used in a future build.

What I really lack is an actual work bench. Even crappy tools need a stable surface, and I haven't got one. My wife tells me there will be one under the Xmas tree, however... Meanwhile, the second 'real' CBG will appear in the photo library today- watch this space!

• ▶ Reply