Replies to This Discussion

Permalink Reply by The Phrygian Kid on July 10, 2014 at 9:02am

um...

but you WANT these things to ground their chassis....

skip the grommet suggestion mate this is not your problem..

you need to go to the auto store and buy a $10 multimeter..

you have a short somewhere

maybe a bad pot, that does happen

• ▶ Reply

Permalink Reply by john mackay on July 10, 2014 at 8:49am

 thank you for your quick reply.if that is the case then I'll fit the coil to wood only.

I'm not going to strip the tintar as you call it  to refit the coil.

it work perfectly ok with a peizo also with playing or trying to play  I don't think I'll need a volume control fitment either.

I'm very pleased what I've made so far .seeing that it is my second make.

if you look in the UK post .I've made a one stringer called the rabit ,have a look and you'll see why.

that also sound nice too.john

oh and my youngest son(28) he please a 6 string guitar and he likes my tin tin!

• ▶ Reply

Permalink Reply by John Sawyer on July 10, 2014 at 3:01pm

You ALMOST have it wired right... Ground that open lug on the pot...

Like PK said, go buy a cheap meter, set it to 20K Ohms and measure the resistance across the coil leads.  It should be around 3k or so, if I recall...  if it's OPEN (-1 on the display) or short (0 on the display) something be wrong...

If it shows a short, make sure you didn't reverse the wires on your output jack... then you would have grounded the hot lead...  To test that for sure, remove the pickup jack and hook it up...

I had an open coil recently... very sad... 

• ▶ Reply

Permalink Reply by John Sawyer on July 10, 2014 at 4:08pm

Even a blind squirrel finds a nut from time to time...

• ▶ Reply

Permalink Reply by john mackay on July 12, 2014 at 3:35am

the jack is wired right other wise the peizo wouldn't work.

I've wired the mag pick up directly to the jack but nothing(just in case the volume knob is faulty)

tried the peizo wired to the knob! to that didn't work either.

any way I've put the strings on now.if I do make a tin tin again I will try what you said .thanks.

• ▶ Reply

Permalink Reply by John Sawyer on July 12, 2014 at 4:46am

Bummer, sounds like you have a bad pickup.

• ▶ Reply

Permalink Reply by robert jones on July 12, 2014 at 9:41am

Careful, if the piezo and mag pup are parallel wired then one will always work even if the other is defunct.

Hmmm, mag pup direct to jack doesn't work....piezo-to-vol-to-jack doesn't work...bad jack? (It happens.)

• ▶ Reply

Permalink Reply by John Sawyer on July 12, 2014 at 9:50am

Good point.  I had a poorly made jack...  If you pushed the plug in all the way, it would move off the tip.  Though from your picture, that does not seem to be the case.

Check your cord?

• ▶ Reply

Permalink Reply by robert jones on July 12, 2014 at 10:10am

Cheap multi-meters are so handy. :-)

• ▶ Reply

Permalink Reply by john mackay on July 12, 2014 at 11:24pm

Careful, if the piezo and mag pup are parallel wired then one will always work even if the other is defunct.

the single coil was removed,I didn't solder the two together as one would still work while the other didn't.

I do have a multimeter. I remove the s/coil altogethe but left the vol/knob on. it is fitted with a peizo now and stringed up.

the big hole where the pick up was I put a piece of wood in it place which looks quite nice. peizo is directly under it.heres a picture...

• ▶ Reply

Permalink Reply by robert jones on July 12, 2014 at 11:57pm

So do you have it working?

I like the fishing theme.

• ▶ Reply

Permalink Reply by john mackay on July 13, 2014 at 4:30am

yes it is working.peizo is wired directly to the jack.

sound nice acoustically. 

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• Next ›
• Page