Using a hinge for a tailpiece?

Hey everyone,

I'm sorting out my build here and I'm struggling with what I want to do for the tailpiece. I was planning on cutting some sheet Al. to create my own (and still may) but have a some chrome trunk hinges here at may work also if I go 3-string.

The three existing screw holes are almost (emphasis on almost) spread to accommodate a 1/2" string spacing but not quite there. That being the case, the two outer strings would have to fan outward some. I could use some coarse threaded rod in my bridge to keep the strings where I want them but not sure if they will stay in the threads because of the angle or want to jump out.

Also, seeing as how it's a hinge with a moving hinge point, will it create enough downward pressure on the strings before the bridge?? It doesn't seem like it would, but I have seen so many people use hinges for tailpieces it must work. Maybe I'm just over thinking it some.

Thanks,

0 members like this

▶ Reply to This

Replies to This Discussion

Permalink Reply by ron carlson on July 31, 2012 at 2:19am

I just noticed the tarp grommets used for vol. and tone trim rings. Very clever also!

▶ Reply

Permalink Reply by David L. on July 29, 2012 at 11:39am

Snake hinges work well

▶ Reply

Permalink Reply by ron carlson on July 31, 2012 at 2:15am

I like those also. Looks like they would provide great anchoring at the rear of the box and a cool look also.

▶ Reply

Permalink Reply by Tom on July 31, 2012 at 9:08am

just goes to show, some times I look, but just dont see !!. Very Cool Idea there !!!!

▶ Reply

Permalink Reply by Jason on August 13, 2012 at 2:22am

One thing: I found that sometimes after dremel-ing a hole where string would run through, the sharp edges of the hole would slice the strings and snap them. You will want to soften your edges. A trick I learned from a guitar player friend is to rub the lead of a #2 pencil in the hole. The pencil isn't really lead anymore, it's graphite which acts as a lubricant and can help keep the strings from wearing out where they rub. This works well on the edges of ferules as well.

▶ Reply

‹ Previous
1
2
Next ›

RSS

Welcome to
Cigar Box Nation

Sign Up
or Sign In

Or sign in with:

The Essential Pages

Site Sponsor

Forum

Blog Posts

Latest Activity

Doug Thorsvik commented on Doug Thorsvik's video

California Dreaming: 3D Printed Cigar Box Guitar

"I agree Alan; she had some serious pipes! Glad you enjoyed this one; it was fun to learn."

4 hours ago

AGP # commented on Wanhavihtahousu's photo

IMG_5132

"Nice Tins, I'm presuming they all have one of those 3 Pole Magnetic Pickups in them ?? :-)"

6 hours ago

AGP # liked Wanhavihtahousu's photo

AGP # liked Doug Thorsvik's video

California Dreaming: 3D Printed Cigar Box Guitar

6 hours ago

AGP # commented on AGP #'s photo

AGP #533 - ''Beware of Wife''

""Thanks A.D." for the very generous comment :-)"

6 hours ago

Timothy Peter Cooper and Sam Tringali joined Cigar Box Nation

9 hours ago

BrianQ. left a comment for Sam Tringali

11 hours ago

BrianQ. liked Doug Thorsvik's video

California Dreaming: 3D Printed Cigar Box Guitar

11 hours ago

Southern Ray replied to Bill Andy's discussion Copper Hardware

"Taffy makes good points. I have no experience either with the paint, but I have a bunch of 50+ year…"

11 hours ago

Doug Thorsvik posted a video

California Dreaming: 3D Printed Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 201st Zoom Mtg 05/06/24. Only 1-finger chords, free songbooks here: https://www.cbgslinger.com/download CBG Songbook.pdf...

14 hours ago

2 Comments 2 Likes