Replies to This Discussion

Permalink Reply by Willy on June 18, 2009 at 3:58pm

I don't have experience shellacing cigar boxes, but I have used varnish over top of a large paper lable on the end of an old tomato crate. This has worked very well and has caused the label to last for over 5 years now. I allowed the varnish to really penetrate (thick covering) the paper label for better adhesion. Maybe someone else around here with cigar box specific experience can shed some better light on this subject.

• ▶ Reply

Permalink Reply by ChickenboneJohn on June 18, 2009 at 6:28pm

I just blow them over with rattlecan clear acrylic lacquer. Make sure the paper is soundly atached, and re-glue any loose corners before lacquering. Spray it in several light coats - don't be tempted to spray a really heavy first coat, as the lacquer can penetrate right thru' the paper and cause unsightly dark spots. I've made 130 plus CBGs and counting, so it does work!

• ▶ Reply

Permalink Reply by Jkevn on June 19, 2009 at 1:50am

I too like to use the spray can acrylic, I prefer the satin finish so it doesn't get all glossy. I've used it on everything from end tables to spray-painted parts, it's durable stuff.

• ▶ Reply

Permalink Reply by J. K. on June 19, 2009 at 2:00am

I read somewhere that you can use decoupage glue like Mod Podge to protect the paper and gives a nice finish to it.
http://www.plaidonline.com/apmp.asp
says it acts as a "all-in-one glue, sealer and finish".

• ▶ Reply

Permalink Reply by One String Willie on June 19, 2009 at 2:49am

Hi Steve-

Just inviting you to consider another way of looking at this, think back to before you started with CBGs: which had more mojo--a pristine tele, or one that looked like it had been played for years? Perhaps it's due to my advancing age, but I like the well-worn look--the world can see that you (or the instrument you are playing) have been around the block.

Although I do make sure the paper is glued down well, I don't put a finish on my CBGs, and I play with fingerpicks. The paper on the face of the CBG where I play is starting to wear through to the wood, and there is crud (presumably an amalgam of sunblock, dirt and sweat) on the face where i rest my right forearm on the box. This adds to the patina. I will acknowledge that my main instrument is a 2 x 6 with a length of broom wire stretched between two nails (which is now starting to look a little beat-up--the antithesis of a highly finished instrument.

Best regards, Willie

• ▶ Reply

Permalink Reply by Steve Becker on June 19, 2009 at 3:55am

Thanks for all the input guys! I think I'll go with the spray on acylic laquer. Just a couple of light coats to keep the worst of the dirt and sweat off the paper. Willie, I do like your advice too. That's why I'm not going to put the coating on heavy, like I said, just a couple of light coats. Now, if I happen to find a nice 100 year old cigar box at an antique shop somewhere, well that one will definatly be all natural.

Thanks again for all the advice. You guys rock!

• ▶ Reply

Permalink Reply by Slowpaw Steve T on February 26, 2011 at 10:07pm

I tested this this morning with some unused cans of spray lacquer that came with some car paint - seems to work a treat on paper cb labels, dries to a nice silky sheen, though will use wood/yacht varnish on my finished bare wood (behind the neck).

ChickenboneJohn said:

I just blow them over with rattlecan clear acrylic lacquer. Make sure the paper is soundly atached, and re-glue any loose corners before lacquering. Spray it in several light coats - don't be tempted to spray a really heavy first coat, as the lacquer can penetrate right thru' the paper and cause unsightly dark spots. I've made 130 plus CBGs and counting, so it does work!

• ▶ Reply

Permalink Reply by Uncle John on February 27, 2011 at 3:50am

Is polyurethane an acryllic?  I recently wrecked a pretty box spraying with poly.

• ▶ Reply

Permalink Reply by Cigar Box Nation on February 27, 2011 at 5:36am

Yeah...um, good luck with that.  ;)

• ▶ Reply

Permalink Reply by Steve Becker on February 27, 2011 at 8:02am

In  the end I decided to do nothing to the paper. I figured its paper, so it will wear no matter what. I have to admit all of that mojo Shane has on his guitar has a certain appeal to it.

• ▶ Reply

Permalink Reply by ANDOMANDO,,also known as ANDY on March 11, 2011 at 3:34am

Try painting layers of PVA GLUE on your box,it dries see through and makes the box stronger.

try it out on a spare piece of paper first,so you can see what happens,

good luck

• ▶ Reply