#1 resource for Cigar Box Guitars, Free Plans, How-To, Parts & More!

So, I am at the Home Depot...

and I am shopping for some more wood for necks, and pickup up some hardware for some builds. After sorting through the 1x2's, trying to find some that don't have warps or bends, I decide to stop by the power tool department just to see what I can see.

For the longest time, I have wanted to pick up a bench planer, but I just could not justify spending 300 bucks on one, even though the prices have come down on them.

So I am looking at the planers they have, and they are still out of my price range. But then I see a 13 inch Ryobi bench plane. It was marked as originally $229.00, but was marked down to $192.00 on sale. I looked under the benches to see if they had any more of them, but this one appeared to be the last one they had.

I grab Brian from the power tool department, and he confirms that it is the last one of that model. I asked if the $194 was the lowest price on it. He pulled out his scanner and discovered that it was discounted down to $137.00 for the floor model. That sounded a whole lot better to me, so I told him I would take it.

He went to put it in the cart and found that it had been screwed down to the wooden shelf it was sitting on. He went to find a screwdriver, and after a long 15 minutes he finally came back and told me that all the cordless drill/screwdrivers had the batteries run down on them, and nobody had bothered to plug them back in. It would have taken a long time to get the screws out by hand, so I told him he could just put it in the cart, with the pieces of 2x6 it was attached to, and I would just take the wood off when I got home.

He did that and then told me he would take another 10% off the price for me. So when I got to the checkout, the $229.00 planer ended up costing me $124.00!! And including the factory warranty.

He shoots, he scores!!!

So I got it home and set it up on my workbench, I found a piece of scrap to test it out on. Worked like a charm, so I grabbed a few pieces of Ipe fingerboard stock that was rough cut and needed planing. In a matter of seconds, they were smooth and even. It would have taken me hours of sanding to get that hardwood flat like that.

I had never used a planer before, but boy am I a happy camper now!! Under a minute to plan 4 neck blanks smooth.

Yee Haw!!!

1 member likes this

▶ Reply to This

Replies to This Discussion

Permalink Reply by Wes "I'm Baaaaack" Yates on September 11, 2011 at 9:06am

I'm jealous. Nice!

-WY

▶ Reply

Permalink Reply by Ron "Oily" Sprague on September 11, 2011 at 9:23am

Green with envy here. :-(

▶ Reply

Permalink Reply by herb Berwald WWW.CigarGuitar.com on September 11, 2011 at 10:57am

Score!

▶ Reply

Permalink Reply by Delvero on September 11, 2011 at 1:39pm

Great deal! Do yourself one favor and put those earplugs in everytime you use that planer!

▶ Reply

Permalink Reply by Henry Strat-o-varius Lowman on September 11, 2011 at 2:05pm

SCOOOOOOOOOOOOOOOOOOOOOOORE!!!!!!!!!!!!!

▶ Reply

Permalink Reply by PapaSimone on September 11, 2011 at 2:36pm

Wow! Great story of triumph!

▶ Reply

Permalink Reply by Jeff "Sweet T" Tinsley on September 11, 2011 at 2:52pm

Outstanding deal!
Listen to Delvero's advice. You want to be able to hear what you build in the future, right? Lol.

My planer is so loud it makes the routers sound like they are whispering.

▶ Reply

Permalink Reply by the anonymous pick on September 11, 2011 at 2:59pm

shhhh .. i just went to my home depot and un plugged all the rechargers ;-}

▶ Reply

Permalink Reply by Diane in Chicago on September 11, 2011 at 3:16pm

Wow! Wonder if there are any left at MY home depot!

▶ Reply

Permalink Reply by Dan Sleep on September 11, 2011 at 4:13pm

Actually, this planer is pretty quiet. I only use this kind of stuff with the garage door open, so most of the noise goes outside. But earplug advice has been noted.

▶ Reply

Permalink Reply by Mungo Park on September 11, 2011 at 5:27pm

Great deal, now the sky is the limit, no board will be safe from becoming a CBG, we will overcome!!!!

Enjoy, Ron.

▶ Reply

Permalink Reply by Roadkill a.k.a. John Maw on September 12, 2011 at 1:34am

I thought you were going to say that you also got 20 necks from the wood the planer was screwed to. There will be no stopping you now.

▶ Reply

‹ Previous
1
2
Next ›

RSS

Welcome to
Cigar Box Nation

Sign Up
or Sign In

Or sign in with:

The Essential Pages

Site Sponsor

Forum

Blog Posts

Latest Activity

A.D.EKER commented on A.D.EKER's video

All You Got to do is put your Mind to it ! BCB - A .D .Eker 2024

" You can Rollerskate in a Buffalo Herd !!"

2 hours ago

A.D.EKER commented on A.D.EKER's video

All You Got to do is put your Mind to it ! BCB - A .D .Eker 2024

2 hours ago

A.D.EKER posted a video

All You Got to do is put your Mind to it ! BCB - A .D .Eker 2024

a Tribute to the Great lyricist Roger Miller ,a adapted version of the Tune " You cant Rollerskate in a Buffalo Herd " whit the refrein , on a four string c...

2 hours ago

2 Comments 1 Like

A.D.EKER commented on A.D.EKER's photo