I think many eventually come to a point where they want to start fretting their guitars. That's where I have arrived. Not knowing much about the procedure, I pretty much jumped into it with both feet.
Finding fret wire was easy--it's actually inexpensive. Where I ran into trouble was when trying to find the right saw for cutting the fret slots. It's just natural for me to try saving a few bucks, but sometimes that inclination works against me, and this is a perfect example.
I first went to Amazon in search of a cheap saw that would serve the purpose of cutting the fret slots. Twice I thought I had found the right saws, twice I was terribly disappointed--either the cut was too wide or it was too narrow. The tang on the fret wire is .023", and apparently the fret slot must also be .023". Taking hints from a YouTube video, I went to the hardware store and bought yet another inexpensive saw, and again I was disappointed. I had purchased three saws and none worked.
So here is the lesson I learned: sometimes it's just better to pay the extra money than keep banging your head against the wall trying to save a few bucks. I now have ordered a "fret saw." from StewMac. What could have cost around $31.00 has actually cost around $60.00 when I account for the three saws I purchased earlier.
If I were to advise anyone on fretting, it would be to buy a saw that is intended for fretting. Don't waste your time trying to find a cheap replacement.
Tags:
My first fret saw was a junior hack saw blade held between two lumps of wood - a design apparently from an early banjo how to book. The blade cut a kerf that was too wide so I cured that with a hammer.
My current fret saw is a standard Jack dovetail saw. It has the added advantage that if you stop cutting just after you can not see under the teeth/light does not shine under the teeth then the slots are just the right depth.
Adjusting the kerf on a saw is not too hard.
- Too wide - hammer flatter
- too narrow - bend the teeth apart wider- aka adjusting the set.
All this is within reason of course and a junior hack saw is the small one- not the full size one.
I want to thank you guys. Glenn Watt especially. I bought a Gitty saw a month or so ago and have worn it out it seems. Don't know if it had defective blade or what. Went to Lowes and bought the pull saw mentioned and it cuts so well I am very happy with it. Makes short work of the Oak I am working with.
To get a clean slot, a fret saw has to have its teeth not larger than the blade's width. So take a blade with the appropriate width and file down the teeth to the width of the blade. But if you do a lot of fretting buy a japanese fret saw that cuts on pull stroke.
So here's the combo that worked for me: the Stanley FatMax 20-331, a 2 lb. deadblow hammer, and the .023 fretwire from cbgitty. The saw measures 0.018" thick, but left a kerf just wide enough for a secure fit. FWIW, the wood in question was maple and was pretty dry -- it'd sat around for 10+ years.
I've since picked up a .57mm (0.224") Japanese fretsaw -- a nice pull saw with a brass spine (http://www.philadelphialuthiertools.com/), but on my current build using solid walnut, the frets seems a bit less secure.
- ER
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans 4 hours ago. 6 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. 7 hours ago. 4 Replies 0 Likes
Started by BrianQ. in Performances, How to Play, Lessons, Concerts on Tuesday. 0 Replies 2 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!