Replies to This Discussion

Permalink Reply by Jon Leslie/Runaway Veal Music on May 5, 2015 at 6:54pm

I tried that but thank you!
I'd suppose it's the 13th fret that's just too high on the low string side ...the other two strings on that same fret are fine which is why it was confusing...I'll try leveling and hope that does the trick.

• ▶ Reply

Permalink Reply by darryl kernaghan on May 5, 2015 at 8:09pm

Don't get too anxious over it Jon,as advised above,just protect your finger board with tape etc,and file/sand them till even,then a light dressing to clean them up and you should be ok

• ▶ Reply

Permalink Reply by Tom T on May 6, 2015 at 4:27am

You may want to confirm that the 13th is too high and the 12th isn't too low. Depending on which it is, the cure changes. A good 18" stainless steel straight edge will make this an easy check.

Check at each string position (top, middle, bottom) and you may find, as Wayfinder says, that the fret is of the incorrect height only under one string. If the fret is too high under just a single string, the hammer-tap solution should work well.

As others have said, this should be a quick and easy cure.

• ▶ Reply

Permalink Reply by Jon Leslie/Runaway Veal Music on May 6, 2015 at 8:57am

Lesson learned and a wealth of information. I tapped the fret even though it was already seated in as far as I thought it would go...not sure if that helped ..then did what tom t mentioned and concentrated a bit more on the obvious 13th fret. It's great!!! The guitar already had a slew of imperfections...hah just like I like (not really). I will be sure to level frets before staining etc. A huge thank you to everyone as usual!

• ▶ Reply

Permalink Reply by Tom T on May 6, 2015 at 9:22am

Hur--ray!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Good Job....

• ▶ Reply

Permalink Reply by Jon Leslie/Runaway Veal Music on May 6, 2015 at 10:01am

I'll keep that I'm mind for sure.thank you for the help!

• ▶ Reply

Permalink Reply by Tom T on May 6, 2015 at 11:44pm

Wayfinder, I need photos of this. I can't quite visualize. Sounds like a good approach if I can figure out how to do it.

• ▶ Reply

Permalink Reply by Tom T on May 7, 2015 at 1:14am

Sounds like a plan.............

• ▶ Reply

Permalink Reply by jawbone on May 7, 2015 at 1:29am

Not sure if this will help or not...
I took the biggest socket that would fit in my drill press, 3/4", I think, and inserted about half the length into a chunk of hardwood, long enough to cover the width of the fret, then use the whole shebang, chucked in the drill press and use it as an arbor press. I'm not sure what pressure I'm getting. My luck, probably just enough to wreck my drill press !!!

• ▶ Reply

Permalink Reply by Tom T on May 7, 2015 at 1:36am

So, you just tap the frets in part way, then place the board over them, then the level, then lots and lots of clamps..........

The 1/4" board is rigid enough?

I will give this a try on my next fret job.

Thanks!

• ▶ Reply

Permalink Reply by Tom T on May 7, 2015 at 11:14am

Thanks for all the details. I think this is a great way to install frets. Even with other variables, I think that this method will get you as close as possible (all things considered). Then, if further leveling is needed, it should be very minor. I'll take that any day......

• ▶ Reply

Permalink Reply by Jon Leslie/Runaway Veal Music on May 7, 2015 at 2:56am

Great!!!

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• Next ›
• Page