I didn't find right discussion for me.
I have new oak guitar neck with 12" (305 mm) radius maple fingerboard.
frets on neck have never been leveled. Just pressed and glued in slots.
Frets are not big frets that some guitars have. Neck is straight because its unfinished half done neck.
I can't buy from stewmac, too expensive. I live in estonia.
All ideas, what someone have done, how and what tools too level guitar frets here.
I know that needle files are are great for this job.
Also right radius sanding block what I don't have.
First I need too check frets levels with long ruler etc. I Have great aluminum tool level for that.
Something like this
Tags:
To level the frets, you can use a mill bastard file or a sharpening stone. The file needs to be flat. I think both of those should be widely available and not too expensive.
Then once you get the frets level, you need to re-crown them back into a curve so that the string is only touching at one point. Otherwise, the string will buzz. Since you can't get a fancy curved re-crowning file from Stew Mac, you can do what they used to do, which is to use a triangular file. Again, this should be inexpensive and widely available.
I have both triangular and flat file. I also have the needle files.
I Don't have the sharpening stone because I'm using japanese
wetstone instead. I have seen curved files in stores. I'm not sure are this in right angel for me.
For the me the biggest problem is frets angle.
Do you mean the radius or the fret profile (like for recrowning?) If you mean the radius, you don't need a radius sanding block. The flat files will be fine if you use them the right way.
This looks like a pretty good video:
http://www.youtube.com/watch?v=4NcgbouuCjE
There are many other videos on Youtube covering fret dressing.
With a radius fret board, I think you will need to improvise an imperfect solution in the absence of the proper tools. Probably careful use of your needle files.
You can also try, experimentally, to use sand paper and a hardwood block with a fret radius (not fretboard radius) sanded in. Just tape up your fret board to protect the wood and don't tape over the fret. Lay a piece of medium coarse sand paper over top of the fret with the rough side UP. Run a block of hardwood along the length of the fret to form a long groove into the block. Once you have a nice deep groove, wrap the paper around the block with the rough side toward the fret and sand it down. This will only do one fret at a time so it will be very tricky and will require many measurements to get all the frets level.
Your best bet is to start with the neck wood perfectly dead true flat, flat, flat. Really flat.
Guys, I had recent build with a way high 3rd fret. I tried a sharpening stone like Phrgian suggested. My stone is about 2x5 inches. I ran it flat and even over the frets and kind of sanded down the high one. Worked great, but got pretty flat on the one fret.
Like Skeesix said, it should be recrowned. But it works fine as it is for me. It's a cbg, not a Martin.
Take a permanent marker(sharpie) and draw a line along each fret. Take two sided tape and attach very fine sandpaper to your yellow level. Work the sandpaper on the level slowly along the length of the neck. Go slow. Once the sharpie marks dissapear off of all frets you should be level and ready for finishing. Hope this helps.
Wade
Some people do same with radius sanding bock.
I have radius on my frets. I Think that help only for flattening frets.
Once you find the proper leveling of the frets, I find that disposable emery boards (the ones used for fingernail/cuticle care) do wonders for re-rounding the fret without scuffing the fingerboard much.For those places you do scuff, the grain is so fine you can polish it up and (assuming that your radius fretboard is ebony colored) a touch of sharpie forgives all.
I don't envy your working on radius fretboard and frets one bit, dj.xsusb. I got so tired of fine tuning the frets on my flat boards that I glued a 240 grit sandpaper to a perfectly straight hardwood stick, started buffing straight down the fretboard until every single fret had the exact same scuff mark, then round and polish each with emery board until they gleam-NO BUZZ!! Much less frustrating for me.
I suppose you could create a properly radiused sanding stick, but unless you have multiple rounded fretboards with the same radius on each, you'd be faster just doing this piece one fret at a time. My sympathies...
Surrfing around the net is a good thing. I found decent offer for fretcrowning file. From Thomann. For estonian to get one is join some multiordering (rada7.ee) i´m useing the http://telli.kynk.eu/ Ah yes the file is http://www.thomann.de/intl/gewa_bundfeile_150mm_hieb_3.htm Just in case i have not ordered or used it! But it seems nice deal!
Started by Bill Andy in Performances, How to Play, Lessons, Concerts 16 hours ago. 0 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Bill Andy 17 hours ago. 5 Replies 0 Likes
Started by BrianQ. in Performances, How to Play, Lessons, Concerts on Tuesday. 0 Replies 2 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!