Replies to This Discussion

Permalink Reply by John Sawyer on July 9, 2015 at 4:58pm

Worst case burn it off with a torch... but outside and don't inhale the fumes...

Sandpaper would clean up the remaining mess...   maybe... 

I would cut at much as I could off with a utility blade first..

• ▶ Reply

Permalink Reply by Graeme L on July 9, 2015 at 5:43pm

Don't know if you guys have Orange Power there in the states but it will loosen any adhesive or the rubber ?   If not I'd try some of the old fashioned acetone Nail Polish Remover, try and squirt some around under the ring and let it soak for a few minutes, it shouldn't damage the chrome at all.......

• ▶ Reply

Permalink Reply by Tom T on July 10, 2015 at 12:00am

Soaking in Acetone would likely soften (melt) the plastic, but unless you have a can sitting around, that's another $8~$10 to buy a can. Maybe the quest for the perfect bowl is not over yet.....

• ▶ Reply

Permalink Reply by Graeme L on July 10, 2015 at 2:26am

Not sure you need to buy a whole can of acetone, a small bottle of nail polish remover would likely suffice, you don't want to dissolve the entire rubber ring just loosen the adhesive gripping it to the metal.  I'd just dribble a little in around one of the edges and et it work its way in and maybe work it a little and let it soak in further as you peel it back from the metal lip?  A small bottle of nail polish remover should only be a few dollars, probably less in the USA!

• ▶ Reply

Permalink Reply by Ron "Oily" Sprague on July 10, 2015 at 3:11am

Sandpaper. Elbow grease. 30 minutes you spent trolling the Interweb for other dishes...

And the cheesy paw prints stMped in the side of the first one will be down inside the box, anyway. Build one with that bowl, make your mistakes with that one, before you get a nicer dish, or even a real spun cone...

• ▶ Reply

Permalink Reply by Nathan Binns on July 10, 2015 at 5:49am

Thanks for the tips. I do have some acetone. And fortunately, as a Canadian, I know all about the magic of Orange Power. I scratched away at it last night for a few minutes in the shop(when I was supposed to be taking out the garbage) and it will come off. Just a pain in the butt. 

I think I agree with Ron though. I hate when I realize I farted around on the internet for longer than it would've taken me to do things "the hard way", which is usually the only/right way to do it in the first place. 

The stamps on the other bowl are quite visible from the back side. It also sounds "dead" when I flick it with my finger. The other bowl has a better ring to it (except for the rubber ring. That still sucks).

• ▶ Reply

Permalink Reply by Ron "Oily" Sprague on July 10, 2015 at 8:47am

Iffen the stamped one don't ring when you flick it, take it outside, get your shotgun, and toss the bowl in the air...Boom! Instant colander.

• ▶ Reply

Permalink Reply by Bama Hound on July 12, 2015 at 7:53am

Of all the possible answers, this one makes the cut for best. (;-D)

• ▶ Reply

Permalink Reply by John Sawyer on July 10, 2015 at 7:17am

there is no problem so great that it cannot be solved by brute force and ignorance...

• ▶ Reply

Permalink Reply by Tom on July 10, 2015 at 12:29pm

 Learn about a product named...GOO-GONE. You'll be GLAD you did :)

It removes caulks & silicones, contractors adhesives,tar, adhesives and tape residues, inks, markers, wax and much more !

Uses no industrial solvents and has no harsh odor.

I buy mine at most any place. Sometimes household cleaning dept, sometimes automotive dept, hardware sections. Even some grocery stores carry it.

• ▶ Reply

Permalink Reply by JL on July 13, 2015 at 2:35am

Just for the sake of adding to the list of what "might work" would be a heat gun on low setting or a hair dryer on high to soften up the adhesive. this works for me taking off price tags and bar codes from stores who should know better than to put non-peel stickers on things, and to remove decorative pony & dinosaur stickers placed on thing that shouldn't have stickers by younglings that aren't old enough to know better.

• ▶ Reply