Replies to This Discussion

Permalink Reply by Eric Shepherd on October 13, 2018 at 6:15pm

No they're still a fair way off Brian.. There is still all the Paua inlay (I think you guys call it Abalone) to do on the neck as well as doing the inlay on the tailpiece..  I'm also tooling about with the use of liquid glass, it's kind of tricky to get it to do what you want it to do.. Cheers for the thumbs up on that Paul, I really do try and make a guitar that not only plays great but looks good as well.. I just wish I could play one.. :)

• ▶ Reply

Permalink Reply by Lonman on October 14, 2018 at 3:39am

I like the look you have with the extra wood on the ends of the CB, will those be stained as well?

• ▶ Reply

Permalink Reply by Eric Shepherd on October 14, 2018 at 7:10pm

Those tailpieces are a bit of a signature of my builds.. I build under the name of Stinking Fish Guitars and the tailpiece is a sort of stylized Snappers head.. The won't be stained instead they'll have Jarrah inlay and partially covered with tinted liquid glass, that's if I can get the stuff to do what I want it to do..  

• ▶ Reply

Permalink Reply by Lonman on October 20, 2018 at 3:05am

very cool, thanks for sharing

• ▶ Reply

Permalink Reply by Eric Shepherd on October 14, 2018 at 7:21pm

Those tailpieces are a bit of a signature of my builds.. I build under the name of Stinking Fish Guitars and the tailpiece is a sort of stylized Snappers head.. The won't be stained instead they'll have Jarrah inlay and partially covered with tinted liquid glass, that's if I can get the stuff to do what I want it to do..

• ▶ Reply

Permalink Reply by Paul Craig on October 15, 2018 at 11:19am

And they also act as weight stabilizers to stay off neck-dive.

• ▶ Reply

Permalink Reply by Eric Shepherd on October 15, 2018 at 3:00pm

Yeah they do.. The key though is to make sure the back of the box is strengthened internally so no undue load is placed on it.. I use a system of ribs and pegs to spread the load so if it cops a whack to the back it's well supported and won't snap off 

• ▶ Reply

Permalink Reply by Cause the Blue rat on October 14, 2018 at 1:43pm

My work bench is what's on my bench. After a few guitar failures it was time to make something different. I have the top support done. I'll be sawing up the 2x6 legs. Getting them in place. Then all I'll need is the top. Got to go get that. 3/4 ply. Total hight will be 36 inches by 72 wide and 38 deep. I can only go 38 deep because that's all that will fit in my trunk.: )

The table clamp will be made like one of these,

$16 twin screw vice,

I'll also have bench dogs in the vice and on the table. Be making a separate 18 x 18 dog hole table top. It'll go between the clamp and the dogs on the table. This table will have dogs every three inches. Will hold wood ( guitar bodies ) in place for routing and sanding. 

I'll get pics of the hole thing when It's out of my kitchen. The only room in the house with an uncarpeted level floor. Well, there's the basement. But I didn't want to drag this thing up the steps. : ). Garage is very unlevel. 

• ▶ Reply

Permalink Reply by Paul Craig on October 14, 2018 at 4:03pm

I'm liking this.

• ▶ Reply

Permalink Reply by Cause the Blue rat on October 14, 2018 at 4:39pm

Thanks Paul. These are hard to screw up so I should be good to go. : )

Up and ran out of time to use power tools. Nothing after 10:00 PM. I got really good neighbors. I knew my garage has a bad slant. But didn't know just how bad. As it sits it's 36 at the far end and 38 1/2 facing. Looks like I'll re arrange the garage and find a more level spot for it. Frame is 36 x 68. The top will have a two inch overhang for clamping all the way around the table. 

Got a lot of straitening up in the garage to do anyway. Next on the list is to get the framework for the supports and shelves in place. Going to use what ply I have so I'll measure then build. Then go to the local lumber yard and get some 3/8 ply cut so size. The last thing will be the clamp. I am SO looking forward to finally having a clamp and dogs. 

• ▶ Reply

Permalink Reply by Paul Craig on October 14, 2018 at 4:59pm

There's always some uneven areas on a concrete floor. Shims for the bottom on the low side?

• ▶ Reply

Permalink Reply by Eric Shepherd on October 14, 2018 at 7:02pm

I just use the lounge floor.. Yep I'm single :)

• ▶ Reply

• ‹ Previous
• 1
• …
• 57
• 58
• 59
• 60
• 61
• …
• 187
• Next ›
• Page