Want to plug that thing in? Here's a place to share ideas about pickups (Both magnetic and piezo) and wiring in volume and tone control, the best options in output jacks, and more!
Remember that C. B. Gitty Crafter Supply is the one-stop shop for all of your CBG Electronics needs!
Members: 747
Latest Activity: Feb 10
MySpace
Tweet
Started by BrianQ. Feb 10. 0 Replies 0 Likes
Good article on pickup simulation from AMZ-FX, written by guitar electronics guru Jack Orman. Basically you can use any pickup, simple enough right? He even makes reference to CBG’S & 3 pole CBG…Continue
Started by ILL GREEN. Last reply by David Bowes Jul 31, 2022. 2 Replies 0 Likes
Hello everybody!Thought I'd drop these nuggets for anyone looking to wire (3) P90s into their guitars.First, the middle pickup must be reverse-wound, meaning you would wind the pickup clockwise. The…Continue
Started by Steve Bookout. Last reply by BrianQ. Jun 15, 2021. 15 Replies 0 Likes
Guys, after assembling yet another 3 stringer with one pick up, one volume pot, and one tone pot, something is amiss. Have never had this issue before. Static noise is heard when the guitar is…Continue
Started by BrianQ.. Last reply by BrianQ. Jun 23, 2020. 3 Replies 0 Likes
Add External Power to anything:Continue
Comment
Generally audio tapers are used for volume and either audio or linear for tone. Audio taper gives an increase pattern that is more natural to the human ear, while linear taper gives an even rate of increase which can seem more sudden. It does seem strange that they would put audio on tone and linear on volume. Could have been a mistake in manufacturing... you see that sort of thing fairly often with cheap knock-off parts. While it would work, you'd probably get better results if you swap them.
Audio taper is a progressive or "bell curve" while linear taper is um. linear.
i think audio and taper are the same...but don't rely on that..
I was scrounging through my parts bin this morning looking for a volume/tone setup for my current build which is using a 4 pole single coil mag pup. Found a pre-wired combo I got a long time ago that came as part of a Fender Jass Bass knock off. I just noticed that the tone pot is a 500k audio taper (the cap is a green chicklet marked "2A473J") and the volume pot is 500k linear taper. Should I switch out the vol pot to audio taper? Why would it be a linear taper to begin with?
sounds like a bad pot
an easy way to test this without unsoldering/soldering would be to hook up a jumper across the pot tabs, shunting the circuit directly to the jack (bypassing the pot)
I already did and there is no noise. But there is no noise when it's all the way up too.
For a test solder the wires from the piezo directly to the jack connector. Does it still hum then?
The license plate and strings are grounded, and I just went through all my solder joints. Everything looks good still have the buzz. Is there a way to determine for sure it's the pot?
Chris, try grounding the license plate & strings.
It could be a bad pot also
Are the strings grounded?
Started by ILL GREEN. Last reply by David Bowes Jul 31, 2022. 2 Replies 0 Likes
Started by Steve Bookout. Last reply by BrianQ. Jun 15, 2021. 15 Replies 0 Likes
Started by BrianQ.. Last reply by BrianQ. Jun 23, 2020. 3 Replies 0 Likes
Started by David L.. Last reply by Ray Stanis Mar 24, 2020. 10 Replies 0 Likes
Started by Adam Jellison. Last reply by Paul Craig Feb 28, 2020. 9 Replies 1 Like
Started by bizzaro guitaro. Last reply by Paul Craig Jan 31, 2020. 16 Replies 3 Likes
Started by John Mark Perchalski. Last reply by Paul Craig Jan 30, 2020. 3 Replies 0 Likes
Started by Holly Hodson. Last reply by KOOL DOG HOOCH Sep 22, 2019. 5 Replies 1 Like
Started by Arthur Payne. Last reply by KOOL DOG HOOCH Sep 21, 2019. 4 Replies 1 Like
Started by James Pobog. Last reply by KOOL DOG HOOCH Sep 21, 2019. 6 Replies 0 Likes
Started by Arthur Payne. Last reply by Arthur Payne May 2, 2019. 5 Replies 1 Like
Started by Arthur Payne. Last reply by ILL GREEN Apr 12, 2019. 3 Replies 0 Likes
Started by Arthur Payne. Last reply by Arthur Payne Apr 1, 2019. 5 Replies 0 Likes
Started by Tim Pannabecker. Last reply by Paul Craig Mar 8, 2019. 16 Replies 0 Likes
Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Slow Blues Dani & Ol' Grey Bear Mar 1, 2019. 12 Replies 0 Likes
Started by ILL GREEN. Last reply by ILL GREEN Jan 9, 2019. 5 Replies 0 Likes
Started by Arthur Payne. Last reply by Paul Craig Dec 21, 2018. 9 Replies 0 Likes
Started by Arthur Payne. Last reply by Paul Craig Dec 17, 2018. 2 Replies 0 Likes
Started by Slow Blues Dani & Ol' Grey Bear. Last reply by Paul Craig Nov 24, 2018. 20 Replies 0 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!
You need to be a member of CBG wiring & electronics. to add comments!