I usually add a "heel" that runs under the neck and extends the length of the box, and also glue-on some sort of wings to support the mounting screws. Then rout a cavity through the lid and into the neck for the pup. Both necks in the picture are set up for the mini humbuckers. You will need to bend the screw tabs out a little bit in order for them to match up with the pickup mounting ring that goes on the outside of the lid. The mounting plate/ring also makes a nifty template for the routing, although you can't tell from the raggedy-ass job I did on these two. :-)
Remove mounting plate from pickup...don't lose screws or springs. Position the plate where you want the pickup to be. Mark with a pencil the holes and the rectangular area occupied by the pickup. Cut out the rectangular area. Drill the 4 holes for the plate, and the two holes for mounting pickup...be sure that the holes for the plate are a bit smaller than the screws, so they hold. The two holes for the pickup mounting screws should be a hair larger than those screws, so the thread don't bind on the box top...makes installing the pickup & springs easier.
Once everything is drilled, cut out and cleaned up, install. Mount the plate first. Then place the two pickup screws through the top of plate. The springs go on the inside, between the bottom of the box lid and the small "ear) on bottom of pickup, where screws thread. Only twist the screw in so it holds, then do the other. Once this is done, you can use screwdriver to continue turning the screws, which will cause the pickup to raise higher...or if loosening the screws, will lower it...do this until the top of the pickup is about 5/16 to 3/8 inch from strings. If pickup is too far away from strings, the signal will be weak. But if too close, the magnets will slow down the vibrating strings, and reduce the sustain (how long the plucked strings vibrate).
Thanks this is the details I was looking for, now I have a better understanding and will follow this when I get started, Thanks again, Sonny
Check out the diagram Reeds posted in this recent discussion. You may find it helpful.http://http://www.cigarboxnation.com/forum/topics/neck-to-box-question
Started by Justin Stanchfield. Last reply by Taffy Evans Mar 20. 9 Replies 2 Likes
Started by BrianQ.. Last reply by MadGomer Feb 27. 2 Replies 4 Likes
Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply 0 Likes
Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies 0 Likes
Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies 0 Likes
Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies 1 Like
Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies 0 Likes
Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies 2 Likes
Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies 2 Likes
Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies 1 Like
Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies 1 Like
Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies 1 Like
Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies 0 Likes
Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies 0 Likes
Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies 1 Like
Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies 0 Likes
Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies 4 Likes
Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies 0 Likes
Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies 2 Likes
Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies 1 Like
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!