Ah got UKE made from biscuit tin; 4 string canjo/gitar made from biscuit tin by jabes. Amp made from MacVities biscuit tin.
Love them , ah do :) Some vids on ma page, butya need to look for them amonst lots of other crap :)
What type of biscuits where in the tin ? is there going to be a biscuit bridge? Persaonally i 'd use a selection box !
Well, Mr Herringboney, ah once had one amde from a packet f cheese and onion. Did not have it long, first time a good film on TV to watch, ah ATE IT , washed down by Coke (the drinkin kind, should add!) ;)
I've built a one string out of an old Oxo tin. It's got a single Piezo inside. Feedback is a bit of a problem but once it's set up it sounds great - very growly considering it's just a tin with a stick in it.
I thoroughly recommend tin boxes - in many ways they have better sound possibilities than cigar boxes. As with any box - whether metal or wood - you need to bear in mind the strengths and weaknesses of the material when you're planning your build.
My favourites so far have been a particular shape that Marks & Spencer used for belgian chocolate biscuits. I don't know if you can get them any more though. See following pics:
I think the curving sides gives those boxes a bit more strength in certain useful ways.
Things to watch out for are:
Tin can result in sharp edges, so be careful to avoid lacerating yourself when working with it. Where possible make safe edges for holes by bending the metal over. See following pic of the way I made a hole for a pickup:
Be careful when drilling as sheet metal can snatch and get generally buggered up if you use a regular twist drill. I found the best way to make the sound holes on my guitars was as compound holes done with with "lip and spur" bits (which are actually marketed as specialist wood drills).
Thin metal has very little bending strength (not that thin wood has much either). If you have a freely vibrating sound board (best for good acoustic sound) then you have to expect it to bow inwards a little under the tension of the strings. Don't worry about that, just make sure you have a bridge that you can adjust for height.
Don't worry too much about age of the tin. Probably true that older ones are made of slightly heavier gauge metal so possibly tougher. Also an old tin might have a nice aged look. But you can get great sounds out of new tins.
Great advice, i'd add that, A good strong craft knife will cut the tins =] The issue with modern tin being thinner. is true ..older tin are thicker and can be made with less bridge support, 'skin' bowing causes tuning stability problems as the bow will change if you lean you arm on the side while playing.
Heres GWYN ASHTON playing one of my guitars from a 55 year old bait tin........ (having a '57 fender JNR helps too =)
I should add that a useful effect of a tin body is that it offers automatic shielding for any wiring inside the guitar (as long as you remember to ensure the body is grounded of course).
mark
Looks excellent, how did you cut the sound holes, was this with wood drills?
David
I've made quite a few instruments with tins, with mixed results. In my experience older tins are generally thicker, and round ones (as opposed to the square ones) hold up better with a bridge on it. Watch out for ones with a rounded lid, they are difficult to get a bridge to sit properly...I used three screws on the one below after struggling to make one the right height, which meant that I could individually set the height of each one.
I have seen people making wooden frames which sit inside tins to add strength and bracing, which might well eradicate that problem. They are pretty easy to work with though, I use a dremel with a cutting disk and bend the metal back like has already been suggested - that way you can use the "flaps" to screw into the neck too.
I`ve made several guitars using tins and found them much easier to work with than wooden boxes.No filing or sanding!
I like the look and they sound cool.
You just have to remember to brace them because most tins are made of very thin material and the main thing to watch out for is when cutting back they are SHARP!
Started by Keith 66. Last reply by Keith 66 Apr 24, 2023. 1 Reply 0 Likes
Started by Sleepy John. Last reply by Jock MacHinery Jun 15, 2020. 12 Replies 0 Likes
Started by David Tarry. Last reply by David Bowes May 11, 2020. 7 Replies 0 Likes
Started by Blind Boy Fullers. Last reply by Blind Boy Fullers Mar 20, 2019. 4 Replies 0 Likes
Started by Seasick Mick. Last reply by Seasick Mick Mar 13, 2019. 18 Replies 1 Like
Started by Alex Rigby. Last reply by Alex Rigby Jan 13, 2019. 3 Replies 0 Likes
Started by John Pilling. Last reply by t-belly johnson Oct 30, 2018. 14 Replies 0 Likes
Started by Sleepy John. Last reply by Sleepy John May 3, 2018. 3 Replies 0 Likes
Started by Rick D. Last reply by Tony Dec 14, 2017. 5 Replies 0 Likes
Started by Alex Rigby. Last reply by Ian Boyd Nov 25, 2017. 6 Replies 0 Likes
Started by Alex Rigby. Last reply by Slow Blues Dani & Ol' Grey Bear Oct 10, 2017. 4 Replies 0 Likes
Started by Steve. Last reply by Steve Sep 13, 2017. 2 Replies 1 Like
Started by Alex Rigby. Last reply by Alex Rigby Jun 7, 2017. 2 Replies 0 Likes
Started by Keith 66. Last reply by Michael Fred Johnson Feb 5, 2017. 8 Replies 6 Likes
Started by Mal Chilvers. Last reply by David L. Oct 13, 2016. 2 Replies 0 Likes
Started by Hubert Knight. Last reply by Hubert Knight Oct 11, 2016. 6 Replies 0 Likes
Started by Philip Hale. Last reply by Philip Hale Aug 5, 2016. 19 Replies 2 Likes
Started by Toofy Peg. Last reply by Fomhorach Jun 14, 2016. 19 Replies 0 Likes
Started by Alex Rigby. Last reply by Fomhorach Apr 27, 2016. 16 Replies 0 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!