Does anyone use pine for necks ? or is it too soft.

Tam

Views: 1700

Reply to This

Replies to This Discussion

There are builders here that have used pine, but it is soft and relatively weak with any length. Even buying oak or maple at a big box store is not much more expensive and is a much better choice. Locally the poplar is cheaper than the pine.
$.02
I started making instruments with pine, cuz I had a bunch of 1x2s hanging around. Free is better than paying for something, a lot of times... at least, it is when you're broke! :-)

But to answer your question, you can do it. I personally have made 3-string CBGs with pine necks and had no problem at all. Using strings 44-34-24 tuned E-B-e, no problem. Granted, they were fretless CBGs, so any bow the string tension may or may not have put on them wouldn't matter much in terms of playability. And you can make a piece of pine look pretty nice, too... also, putting a fingerboard on it might help in terms of stability.

That said, I did give one of these pine neck'd CBGs to a friend of mine... and he said the neck bowed on him, pretty badly. It wasn't until later I found out he tuned it all the way up to A without putting thinner strings on it.

Pine is easier to work with than oak or maple, and some people say it's a really good tonewood. It is very soft, though, and dents very easily. For that reason alone I prefer not to use it... why bother putting in all these hours of sanding, finishing and what not, just to have one careless moment and *DING!* Sure, you'll put dings and dents into it anyway over time... but lately, I haven't used any pine.
pine is a great tone wood but for the prince of 1x2 maple (89 cents a foot) i think i would spend a few bucks on maple for a neck.
Thank's for the answers Guys.
I live in Scotland and our main DIY store is B&Q pine is about all I can get there.
I will have to visit a sawmill to get some oak. I have been using oak from a coffee table that my son ruined with cigarete.

Tam

I use B&Q 38 x 25 sawn softwood for my workshop kits..over 1000 of 'em made in my "Make and Play" sessions so far and they work fine. Glue a hardwood fretboard to the top and it'll be OK. It's cheap and it works..hardwood is nicer, but oak is hard to work.

what about cedar? i recently got some lengths of 4 x 1 cedar and was thinking about necks but it feels very light.
stronger than pine though?
I have used pine but I dont if I can get out of it.If I have to use it in the future tho ,I'll cut 2 pieces for the neck, laminate them together so the neck is stronger then a single piece of pine.
I now use mostly poplar and thats how I do my poplar necks too for 3 stringers.What you see on my necks if you look close is a single seam under the 2nd (middle) string where the 2 pieces are glued. It makes for a very strong neck that has always ( so far) stayed where I put it.
I have no idea. I have a thin slice of cedar I'm trying to get some fingerboards from, but my slice has so many damn knots it's hard to get 'em without breaking.

c# merle said:
what about cedar? i recently got some lengths of 4 x 1 cedar and was thinking about necks but it feels very light.
stronger than pine though?
I used a pine 1x2 on my first 3 stringer, just because that's what I had laying around. It was a fretless CBG, with a shorter 21" scale length. It had a nice warm growly tone. The neck seemed a little unstable tuning-wise, but like one of the other posters was saying, laminating two or more pieces of wood together would help with that.

Pine is a great overlooked tonewood, mainly because its soft and dents easily, at least for big factory production operations.

Spanish cedar is the preferred neck wood for classical guitars.
Okay, Pine is a sort of specialty for me so I will add my 2 cents if you don't mind...Pine is a very unique specie of wood. Yellow pine with no heart is soft and not a great choice. However, heart pine is about 25% harder and antique heart pine is about 50% harder. My company manufactures flooring in both Yellow Pine, Heart Pine and Antique Heart Pine flooring. I will tell you, vertical grain antique heart pine is twice as stable as oak or maple and just as hard if not harder. As the wood ages, the resins in the heart wood crystallize and get harder and harder. Find yourself a nice piece of old, vertical grain heart pine and you will not be disappointed in the results. I promise you.

I found this comment very helpful.  I was given a 4x4 rafter from my Great, great grandfather's log house that he had hand hewn (with an ax!) from loblolly pine.  I wanted to use some of it for a neck because of the good mojo it might carry.  But I had questions about the suitability of the wood.  But the rafter is just about 200 years old.  So I'm thinking the crystallization you referred to applies in this case.  There are also some holes from powder post beetles, the bugs have been killed.  But  don't believe the beetles have done much structural damage and the holes can be filled.

Thanks for posting this.

Hey Bobby - Not to side track your plans but I would keep that rafter intact - maybe use it as a rack for your CBG's or something - but then again, I'm a bit sentimental.
The mojo might still transfer from them hanging there!!!

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on Dar Stellabotta's video
Thumbnail

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

"i See Your ready to Blow away the GRAND STADIUM ! tree strings more of DAR DELIGHT !! Shine Girl !…"
4 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you for the kind comments Doug! Glad you liked the Picture !"
4 hours ago
BrianQ. commented on Dar Stellabotta's video
8 hours ago
BrianQ. liked Dar Stellabotta's video
8 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
11 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
11 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
12 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
12 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
14 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
14 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
15 hours ago
A.D.EKER commented on Ricky D's photo
15 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->