Hey everyone,

I'm sorting out my build here and I'm struggling with what I want to do for the tailpiece. I was planning on cutting some sheet Al. to create my own (and still may) but have a some chrome trunk hinges here at may work also if I go 3-string.  

The three existing screw holes are almost (emphasis on almost) spread to accommodate a 1/2" string spacing but not quite there.  That being the case, the two outer strings would have to fan outward some. I could use some coarse threaded rod in my bridge to keep the strings where I want them but not sure if they will stay in the threads because of the angle or want to jump out.

Also, seeing as how it's a hinge with a moving hinge point, will it create enough downward pressure on the strings before the bridge??  It doesn't seem like it would, but I have seen so many people use hinges for tailpieces it must work. Maybe I'm just over thinking it some.

Thanks,

RC

Views: 4412

Reply to This

Replies to This Discussion

How wide is your neck gonna be? I make mine 1 1/2" wide so a 3/8" to 7/16" spacing works perfect for mine. Gives me 3/8" between strings and 3/8' left to the outside of my neck. As far as hinges go I use them about half the time, make sure your string retainers are big enough so as to not slide right thru the hinge holes, if you have trunk hinges the holes may be pretty big. I know you can slide the string back trhu the retainer and sort of half hitch them to the hinge but I'm not a big fan of that as it makes the string awfully brittle at the bend point.

Hey Maddog,  

The neck will finish out at 1 1/2".  I had read (somewhere) that keeping your high and low strings as close to the neck edge made for easier playing, slide wise. So with that in mind, I just figured that 1/2" spacing was about right without getting too wide between the strings.

I'll have the measure the hinge and see what I'm working with exactly.  It's less than 1/2" .

Thanks,

RC

You're overthinking it. >:-E Go Nike: Just Do It.

However, getcha some reeellly small washers, and use them to plug the holes if they're too big. Or use pop rivet ferrules. Or bicycle spoke nipples. Or loop the strings through their own ball ends. It'll create enough downward pressure. Once you tie the strings on, however you end up doing it, and tune them to pitch, I can just about guarantee you that's the last time that hinge will move as a hinge ( as far as you can tell), until you restring.
If the holes are too big to capture the ball ends the best way to go is dremel a wee slot forward from em like this one, so you can just drop the ball thru and pull it forward to lock it in. This is a real common tailpiece arrangement. Little washers etc will serve to annoy you down the track and introduces possible rattles etc, it's unnecessary extra parts..
http://i950.photobucket.com/albums/ad348/jeflong/2012%2012%20VeryMe...

It doesn't matter so much if the holes don't line up exactly, but it does create tension that causes te bridge to want to move, so you want the hinge nicely centered so the tension is pulling the bridge downward just equally to how it's pulling it upward. Otherwise you wind up needing to glue the bridge down. Which is not te end o the world anyway. Have fun
I love hinges, the work great. In stead of using the holes drilled for screws, i drill my own. Just be sure you dont leave a sharp edge on the holes, clean 'em up with a file or sand paper.

These are the ones I have... http://www.rockler.com/product.cfm?page=450   Rockler refers to them as trunk hinges at their store here in town.  They are not as big as what you might think when the subject of trunk hinges comes up.

The existing screw locations are pretty dang close to ideal so I think I'm going to give it a go without drilling new. These would really be cool if the short side (2 screw leaf) of the hinge mirrored the string leaf for better anchoring  but should be pretty secure with a thru neck. 

Ooooh, this just gave me and idea. if you mount an arm of some sort to the hinge part that is holding the strings you would sort of have whammy bar! Off to the hardware!

Those Rockler hinges look perfect for tailpieces, for 3 stringer anyway.

They are pretty cool hinges.  Weighty, and have some depth to them also.  The spread on the outer holes (center to center) measures at 3/4".  

When I made my first CBG I used a small brass hinge on the tail piece. I screwed the hinge in place so it folded over the end of the tail piece, then drilled small holes through the tail piece itself. I then "borrowed" three small buttons from my wife's sewing box. I ran the strings through the buttons, then through the holes in the tail piece and through the screw holes on the hinge. It worked good for me.

Sometimes i use a cabinet hinge. Just cut the hinge off, you now have a tacbg 002il and a bridge.

Now that's clever.  I like it.

RC

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
13 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
13 hours ago
Kent Thurston updated their profile
14 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
14 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
15 hours ago
Poorness Studios liked A.D.EKER's video
16 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
17 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
19 hours ago
A.D.EKER commented on A.D.EKER's video
23 hours ago
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
23 hours ago
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday
Papa D commented on Papa D's photo
Thumbnail

american1 Sun Glo

"Thanx AGP & Doug..  4 more coming soon"
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->