I'm going nuts, the answer to how high to set the nut varies from the thickness of a playing card, the thickness of a dime to the height of the first fret plus .030. This is my first build and I want it right and to sound awesome. I'm using a blank bone nut, a quaternsawn oak fretted neck from CBGITTY. Also I'm putting in a "Deltabucker pickups with an adjustable bridge. Any help, thoughts or constructive criticism are welcome. Thanks

Views: 382

Reply to This

Replies to This Discussion

Don't sweat it, as long as the strings clear the first fret it will be OK. Once you've got that done you can tinker with it until it's as you like it. Making a simple guitar is a practical task for a practical person, so I'm sure this will be the least of of the things you have to deal with as a first-timer.  Good luck, enjoy the process and don't worry about it too much - use your hands, eyes and commonsense. I've made nearly 1400 cigar box guitars, so I think I'm in a position to say, "don't worry about it"!

When setting the string  height over the first fret there are a couple of things I would suggest to keep in mind, even for a beginner. Are you playing fretted notes only, or using a slide. Do the strings have a low tension favored by players that fret notes and cords, or a higher tension favoured by many slide players.

If playing fretted notes max .020 is as high as you need to go I recon, that's electric guitar setting, acoustic guitar max .024,  but Id start a bit higher and cut the slots deeper to suit your feel. If playing slide, thinking about string height, slide weight, and string tension will help avoid rattling of the slide on the frets.

The slots should be just deep enough to have at least a third the string diameter above the slot/top of nut.

Having watched a mate of mine build two CBG guitars, I can better understand the challenges faced by newcomers. As mentioned enjoy and don't sweat the small stuff. I'm sure this is the first step to a few better instruments.

Taff

I want to play both frets and slide. I'm going to be using Southbound Blues Blaster strings from CBGITTY an open low G (G,D,G)#1 - .044" Nickel Wound, #2 - .034" Nickel Wound and #3 - .026" Nickel Wound strings. I've just only drilling the tuner holes yesterday and I'll be (trying) cutting the nut slot tomorrow and shaping it.
I'm still waiting for my nut files to get here so I can have the correct radii and slot width for each string. I'm taking it "one day at a time" and trying not to over think this. I made a small mistake yesterday, instead of drilling my tuner holes at 2-1/4 for my left side set up, I ended up at 2-1/8 center to center, leaving me to set the right side tuner at 1-1/16 centered . It looks ok but don't think it will be a problem. I don't want to cut the nut slot to deep so I'm going to round off the corners, cut a 1/8 inch deep slot for the nut, see how it looks and let it be till I string it and make down adjustments from there. Like I said I don't have the strings on yet but I'm getting there. Thanks for helping this first timer.

Hi, a safe way to get the slot depth, ball park first time, is to stack the required number of feeler gauges on the fingerboard , to match the fret height, then put on top of that stack the feeler gauges needed to get the required distance from the fret to the bottom of the string/slot. Slide this pack up to the nut and file down till the file just touches the top feeler gauge. Fine tune from there.

The nut action I mentioned earlier relate to the bass/ wound strings, on a six string guitar I would normally go lower for each string 6 down to 1, There is less movement in the higher vibrating strings so I set them closer to the frets. To give you an idea I set acoustic's at .020 to .012

Taff

don't overthink it.

if the slot is too deep the string buzzes on the first fret, if the slot is not deep enough your fingers will ache trying to press the string down to the first and second frets.

press the string down between the second and third fret,

if the string touches the first fret you went too far, but if the gap between the string and first fret is big enough for two credit cards, you ain't gone far enough.

inbetween is comfort, preference, and opinion.

Hi Larry, here's another tip to help from going too far with the slot or judging the nut height, cos going to far on a bone nut can work out expensive.

Get a pencil long enough to lay along the first 2-3 frets, then shave and sand it in half lengthways, so the lead is just about showing along it's length. 

Then lay the pencil on the frets move it up to the nut and make a line on the nut, this will be the height of the top of the frets. keep your slots above the line and you should not go too deep. 

I've been using the same pencil for about 25 years for this job.

Taff

Thanks everyone for all the information, I'll refer back to it when I string it up and start my string fine tuning adjustments.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->