Long time guitar player here, but I'm mostly an electric bass player these days. Anyway, someone posted a link to a Samatha Fish video on the TalkBass forum a couple of weeks ago. That put a burr under my saddle re- CBG. I have a tad of building experience, I made two electric bass guitar bodies last year. Paired with bolt-on commercial necks, that was fine and worked well.
Anyway, low and behold last week at the community garden, there's a wooden cigar box sitting on the "Free" shelf. The guitar gods had spoken, apparently.
Anyway, I snagged it and used the community shop CNC laser to burn an F-hole in it yesterday. Soaked some hardware from the junk box in vinegar night before last to age it. That worked well. Next up - hunting for neck wood. I think I'll buy a pre-slotted fretboard to epoxy to the neck.
Tags:
Position markers laid out on the fretboard and upper side of the neck. Light coat of Danish Oil to seal the wood in preparation for CA gluing the markers.
Neck is walnut. Sadly, not exactly quarter-swan. Almost exactly 1.5" by 0.75". Rear of neck has only been rounded over with a 3/8" "router bit, so I have some shaping to do. But it seems appropriate to do the markers first, while the back is still mostly flat.
Interesting thanks. Not too worried about the unplugged sound, frankly. I'm prone to practicing while others are sleeping. If it's too "responsive', I'd likely wedge the top with some foam or whatever.
Seems that it'll look funny with the FB not snugged against the box. I guess it's a cigar box, it already looks funny.
Re- markers before fretting. Totally agree, but I bought a pre-fretted neck, so I was kinda stuck.
Good afternoon in the shop.
- Neck shaped. All done with orbital sander followed by hand sanding in grain direction.
-Walnut supports cut and glued into box. The tail one is cut back on the lower half to allow more room for controls.
-Neck cut back for box top and also cut back at angle to (hopefully) give better string angle, higher bridge etc. Found good advice on this somewhere. I marked the one end 1/4" deep and the tail end 1/2", then hit it with the big bandsaw. According to my (poor) geometry, 1/4" drop across 8.5" is somewhere in the ballpark of 1.5 - 2 degrees.
Hi Lark, if I want to raise the bridge height I would tilt the neck back. If as you explained you lower the tail end that would tilt the neck end up. Raising the string action, so would mean lowering the bridge to get the desired action.
Tilting the neck back lowers the strings to the frets, this allows for a higher bridge setting. Maybe that's a typo re your deeper recess at the tail end. Forgive me if I have misinterpreted your meaning.
Cheers Taff
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. 4 hours ago. 4 Replies 0 Likes
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by A.D.EKER yesterday. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango on Tuesday. 4 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods on Saturday. 7 Replies 1 Like
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Carl Floyd Mar 1. 15 Replies 0 Likes
Started by Joe in Performances, How to Play, Lessons, Concerts. Last reply by Carl Floyd Feb 29. 13 Replies 0 Likes
Started by Chance in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Feb 22. 12 Replies 1 Like
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!