How to taper a Cigar Box Guitar neck with hand tools

I've been meaning to have a proper attempt at this for a while - all of my previous builds have used a straight neck and to be honest there's nothing at all wrong with that. A 3 or 4 string guitar doesn't really need a taper in order to be playable. I do however think a tapered neck looks more elegant, and it does feel nicer to play. I believe this would normally be done with power tools such as band saws and disc sanders. I try to do everything with hand tools. Here's how I did it:

(My usual disclaimer applies: I am by no means saying that this is the only way to do this, nor is this entirely my thoughts or my research. I consider everything I do a collaborative effort with everyone else in this community)

Another important consideration with  job is the order in which these steps are taken - there are some steps which need to be taken whilst both the fretboard and the neck are still square and true - I can't imagine trying to mark or cut the fret slots after the taper! I suppose one could use a bevel gauge but I don't have one.

So, to begin with, I measured out the fret locations in exactly the same manner as I always do. I also marked the centre line down the fretboard and marked the locations of the marker dots.

I made a couple of calculations at this point about string spacing. The neck blank was 42mm wide, so with a 12mm string spacing at the bridge there would be 3mm clearance from the string to the edge of the fretboard at either side (12+12+12+3+3=42mm). I decided to go with an 8mm spacing at the nut, as this is what I have on my 5 string banjo and it seems to work well. Therefore my total fretboard width at the nut would need to be 8+8+8+3+3=30mm I made a solid pencil line connecting the 2 points all the way down either side of the fretboard.

I decided to cut the fretboard to shape before gluing it to the neck, so that's what I did next:

To do this I clamped the piece to my bench and used a Surform, then a block plane, then a file, then 80 grit sandpaper to get right up to the pencil line. I kept sighting down the line and lying the piece on a flat surface to check for consistency.

Once I was happy with this I glued the fretboard to the neck and left it clamped overnight. Once the glue had set it was time to start shaping the neck blank to fit the fretboard. I had a couple of ideas on how to approach this, but in the end I used my #2 and #4 Continental hand stitched rasps. They remove material quickly and accurately. If you try this with a crappy cheap rasp it may end in tears.

I clamped the piece to my bench and carefully removed the wood from the neck to match the pencil line on the fretboard. Once I was happy with it I switched over to a flat file, then to sandpaper to smooth out the surface. At this stage I clamped the neck so it was sticking out from the bench so I could easily sight down it.

The process of shaping the neck by hand took over an hour, so it certainly adds time onto a build. The following day it was time to shape the back of the neck. I am a lot more well versed at this so it was a little quicker. It was slightly trickier than shaping a straight neck, however.

As usual I used a spokeshave, rasps, files to do the rough shaping, then moved onto a long strip of 60 grit paper across grain (shoe shining style). Of course after this make sure to sand over everything with the grain so as not to introduce unsightly scratches. It all turned out pretty well:

The next step was to move on to installing the frets, which was pretty much the same process as with a straight neck, only you will need to cut the fret wire at different lengths to fit the width of the neck.

I think it turned out pretty well!

Thanks for reading! If you fancy a bit of a challenge, by all means give it a go.

Richey

Views: 7912

Comment

You need to be a member of Cigar Box Nation to add comments!

Join Cigar Box Nation

Comment by Smoke Guitars on October 10, 2017 at 1:02am
Would love to give this a try on a 3 string. Would you take off another 8mm? Seems like it may be a bit excessive, what are your thoughts?
Comment by Jerry Jordan on April 12, 2017 at 1:49am

Thanks, good stuff, gonna give it a try..

Comment by RonCrosswhite on March 1, 2017 at 3:21am

Thank you for posting this. I've been thinking about how to do this for a while.

Comment by Fomhorach on November 15, 2016 at 1:41am

Saw this post pop up on Facebook and I thought I would add something.

I don't always taper the sides, I like a straight neck for 3 stringers but I always taper the back of the neck. You can use this taper thickness to guide where you want your neck bow to be after stringing.

Most times a 3 stringer does not need a truss rod for strength true, but having a slight bow is one of the things needed for proper set up. Your wood will bow slightly over time due to string tension and it can be guided by the use of the back taper of the wood. If you taper down to the 16-17th fret you get your bow further down the neck. Tapering down the the 10-11th fret will push the bow further up the neck. It's handy to consider this bow depth displacement when you design the guitar for different weights of strings.

Comment by Bluesheart on April 3, 2015 at 10:12am

very pretty and the taper sure is graceful.

Comment by Richey Kay on March 27, 2015 at 7:01pm
It's quarter sawn English oak, grown about 30 miles away from me Jef. And thanks mate! You've made my day :-)
Glad others are finding this useful too.
Comment by The Phrygian Kid on March 27, 2015 at 12:16pm
Is the neck American ash?
Comment by The Phrygian Kid on March 27, 2015 at 12:15pm
I think your recent cigar box guitars are among the nicest this sites ever seen mate ******
Comment by Tom T on March 27, 2015 at 12:45am

Nice information. I have been considering a tapered neck and this how-to helps understand how to approach it.

Thanks

Comment by 14 buck bass (aka antonio) on March 26, 2015 at 6:11am

totally answered my question on fret board before or after neck , I was wondering about that . great tutorial and tip, and method. I use a bevel guage . but im likin this way more

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
1 hour ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
1 hour ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
3 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
3 hours ago
A.D.EKER commented on Ricky D's photo
3 hours ago
A.D.EKER commented on A.D.EKER's video
3 hours ago
Keith Rearick liked Doug Thorsvik's video
7 hours ago
Keith Rearick liked A.D.EKER's video
7 hours ago
Keith Rearick liked Doug Thorsvik's video
7 hours ago
Keith Rearick liked Ricky D's photo
7 hours ago
Keith Rearick liked Ricky D's photo
7 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->