thanks...
Hi Vinny there are a number of ways to approach this. Many builders get a long drill bit and drill in through the neck cavity for a cable run between pickup slots. A les paul has a cable run (for the pickup selector in the top there) routed into the rear half before the maple cap is glued on. For your first couple I'd strongly recommend Leo Fender's approach, take a look at a stratocaster - almost the entire circuit (everything but the output jack and the earth to the bridge) is preassembled on the rear of a snazzy looking pickguard... This way it isn't too critical if you mess up a few of your first attempts with the router or chisel, they'll be covered over.
You don't NEED a router (although they are very very handy for solid bodies) you can totally get by with a bench drill, a set of forstner bits and some sharp chisels. Once the slots are in you make your cable runs between em with long drill bits and careful angles
Good luck :)
looks like the way to go...a cigar box size strat...i'll keep this post update...thanks
Started by T-Gripped. Last reply by ILL GREEN Mar 2, 2019. 5 Replies 0 Likes
Started by Tex Pierce. Last reply by Tex Pierce Sep 30, 2017. 6 Replies 0 Likes
Started by Nick Johnson. Last reply by Paul Craig May 28, 2016. 1 Reply 2 Likes
Started by Richey Kay. Last reply by gary sheldon May 8, 2016. 7 Replies 2 Likes
Started by Richey Kay. Last reply by Richey Kay Jan 26, 2016. 5 Replies 8 Likes
Started by Kel Wilson. Last reply by Matt McCarthy Dec 12, 2015. 6 Replies 1 Like
Started by vinny brig. Last reply by Ricky Johnson Nov 10, 2015. 5 Replies 0 Likes
Started by G.S. Monroe. Last reply by The Phrygian Kid Nov 5, 2015. 3 Replies 2 Likes
Started by Leadfoot T. Last reply by 0xp0lyyfdwzrt Nov 4, 2015. 4 Replies 0 Likes
Started by Randy S. Bretz. Last reply by Randy S. Bretz Nov 25, 2014. 2 Replies 2 Likes
Started by The Phrygian Kid. Last reply by The Phrygian Kid Jan 13, 2013. 7 Replies 0 Likes
Started by Bob Lumpkin. Last reply by The Phrygian Kid Aug 18, 2012. 3 Replies 0 Likes
Started by Steve Terry. Last reply by Bob Lumpkin Aug 18, 2012. 2 Replies 0 Likes
Started by jabes. Last reply by The Phrygian Kid Jul 11, 2012. 3 Replies 0 Likes
Started by Randy S. Bretz. Last reply by Wichita Sam May 17, 2012. 3 Replies 0 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!