Last night I put together a quick build using an old "Canadian Club" gift box that my wife had been holding on to for a few years. I already had the neck built for a hubcap guitar so there wasn't much to do to finish it up.

The box is 9" square, and about 3.5" thick. I put wooden cross braces across the back of the neck inside the box to help stabilize the box.

The sound is still a bit muffled... would it help to add a sound hole or two? I have some 7/8" brass grommets I could use, but since I haven't built one of these before I'm not certain where the best place to put the hole would be.

Helpful advice would be much appreciated.

Views: 1070

Reply to This

Replies to This Discussion

no it doesnt really help at all imho.

next time don't brace the top at all, just brace the sides, the tin will brace the top plenty.  A nice tall bridge and corresponding neck angle helps a lot too.  I avoid cutting or altering the lid at all

 

To test what Phrygian is saying, put some pressure on the strings behind the bridge and strum it. It looks like there is hardly any pressure on the bridge. You can move the bridge back to about an inch and a half from the back and play it too to test it. Your scale will be off, but it should sound better.

Move your neck farther into the box all the way to your last fret so your bridge is nearer the edge of the tin. Then drill new thru holes for the strings and whack off the omit tail. That should put more pressure on the bridge and provide a more rigid part of the lid to resonate.

if youre gonna pull the neck out dont stop there, splice a body end scarf join to create some pitch and make a taller bridge..

its not as difficult a job as it sounds, as long as you can access a bandsaw and you do have a bit of neck length to spare there.  Ive done this mod myself to improve a cbg, message me for more info if you like :)

Can you show me an example of this? I think I know what you are suggesting, but a pic being worth 100 words and all, well you know...

Shortening the neck wouldn't hurt anyway, as it is right now it's about 1" too long for the Martin strings I have fitted.

I like being a contrarian, so here I go...

A soundhole may help or it may not. On my lunchbox build I did some testing - opening the lid a bit and closing it, comparing the loudness. When closed the sound was a bit muffled. I added an soundhole and it was louder. 

I don't know much acoustic theory but it seems a soundhole gives the sound somewhere to escape. Subwoofer enclosures have a soundhole, so do acoustic guitars and such.

Your mileage may vary, though.

Hmmm.... perhaps I might consider drilling a circular grid pattern of 3mm holes in the back, like a speaker grille on an old radio or dashboard. Giving the box an opportunity to breath a bit *might* open up some of the muffled tones I am getting. And if not, I could always cover the holes with a sticker or two...

  1. I've never put soundholes on a tin guitar (three string/unfretted) and they sound mighty fine (wired with piezos), but what others said: more string tension on the bridge is better.
  2. That is a straight-up awesome tin you acquired there.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->