How many different Ideas are there out there for tuners?

Views: 1929

Replies to This Discussion

you might try the search function. I just did and there are 15 pages worth of posts... ought to be a good idea or two there....
Hey Steve-- My last project was a 3 string made with eyebolt tuners. I didn't think it was gonna work, but it did. It's a little bit of a pain to get
into tune, but once you do it stays there. I started with a modified slotted headstock--I drilled big holes for the strings to attach to the tuners. Here's a pic:

On the eye side of the bolt I've just put a plain old fender washer. On the other, a fender washer and a wingnut. I originally had a lock-washer between the wingnut and the fender washer, but that caused a lot of hassle when I needed to make adjustments, so I just took it out. Seems to work fine without. I drilled holes in the shaft of the bolt to stick the string through. I found it helped to flatten the spot off with my dremel so the drill bit wouldn't deflect off to the side. What I've done is crank the wingnuts down so that the string tension doesn't wind them backwards, but so that I can still (barely) make adjustments myself.
BT, That is a very nice looking headstock.... the bevel sanding out of the slots and the way you cut the top really works together... nice job. the best, Wichita Sam
BT Cohosh said:
Hey Steve--


My last project was a 3 string made with eyebolt tuners. I didn't think it was gonna work, but it did. It's a little bit of a pain to get into tune, but once you do it stays there.


I started with a modified slotted headstock--I drilled big holes for the strings to attach to the tuners. Here's a pic:


On the eye side of the bolt I've just put a plain old fender washer. On the other, a fender washer and a wingnut. I originally had a lock-washer between the wingnut and the fender washer, but that caused a lot of hassle when I needed to make adjustments, so I just took it out. Seems to work fine without.

I drilled holes in the shaft of the bolt to stick the string through. I found it helped to flatten the spot off with my dremel so the drill bit wouldn't deflect off to the side.

What I've done is crank the wingnuts down so that the string tension doesn't wind them backwards, but so that I can still (barely) make adjustments myself.
BT, Love the way you drilled holes for each eye bolt ....Looks great- I may have to steal your idea :-)- running low on turners!!!! I used eye bolts on my last build but I used elastic stop nuts in place of the wing nuts . You just tighten them down until they don't back off . Then I cut out one large slot for the all three eye bolts..
Thanks for the kindness. I'm actually planning on sculpting the headstock a little more--I didn't want to put too much effort until I knew if it was going to work.

I should probably just leave well enough alone, but I've developed an addiction to my Dremel drum-sander....

BTW, I'm currently working on a ukulele version of this design built into a tiny Punch box. I'm curious to see how it works with 4 strings.
with tine eyebolts???? that ought to be cool looking...

BT Cohosh said:
Thanks for the kindness. I'm actually planning on sculpting the headstock a little more--I didn't want to put too much effort until I knew if it was going to work.

I should probably just leave well enough alone, but I've developed an addiction to my Dremel drum-sander....

BTW, I'm currently working on a ukulele version of this design built into a tiny Punch box. I'm curious to see how it works with 4 strings.
I'm actually using thumbscrews -- I can't remember what gauge, but considerably smaller than the 1/4 inch eyebolts. I'm a little worried about getting the string holes drilled in the thinner shafts, so I may have to come up with an alternative for securing the strings.
Your headstock looks cool ,I thank you for your idea, I will have to try this out!
BT Cohosh said:
Hey Steve--


My last project was a 3 string made with eyebolt tuners. I didn't think it was gonna work, but it did. It's a little bit of a pain to get into tune, but once you do it stays there.


I started with a modified slotted headstock--I drilled big holes for the strings to attach to the tuners. Here's a pic:


On the eye side of the bolt I've just put a plain old fender washer. On the other, a fender washer and a wingnut. I originally had a lock-washer between the wingnut and the fender washer, but that caused a lot of hassle when I needed to make adjustments, so I just took it out. Seems to work fine without.

I drilled holes in the shaft of the bolt to stick the string through. I found it helped to flatten the spot off with my dremel so the drill bit wouldn't deflect off to the side.

What I've done is crank the wingnuts down so that the string tension doesn't wind them backwards, but so that I can still (barely) make adjustments myself.
I've drilled out tuner posts to larger sizes and have drilled new holes in smaller bolts. A good tap with a center punch is usually all that's needed... that and a good vise...

the best,

Sam


BT Cohosh said:
I'm actually using thumbscrews -- I can't remember what gauge, but considerably smaller than the 1/4 inch eyebolts. I'm a little worried about getting the string holes drilled in the thinner shafts, so I may have to come up with an alternative for securing the strings.
A good vise.... You wouldn't believe how many time I've thought to myself how handy one of those would be....

I'm working under pretty primitive conditions--my vise is my thumb pressing whatever it is against my saw table. Probably not shop-teacher approved.

I'll have to watch the garage sales this summer....

Wichita Sam said:
I've drilled out tuner posts to larger sizes and have drilled new holes in smaller bolts. A good tap with a center punch is usually all that's needed... that and a good vise...

the best,

Sam


BT Cohosh said:
I'm actually using thumbscrews -- I can't remember what gauge, but considerably smaller than the 1/4 inch eyebolts. I'm a little worried about getting the string holes drilled in the thinner shafts, so I may have to come up with an alternative for securing the strings.
Here's my take on the eye bolt tuner. I've got another easier idea, but we'll see if I get around to trying it out. If you're lucky, like two out of three for me, the wing nuts only lock the bolt instead of holding the tension.

Cohosh - Didn't see your post before I posted mine. I guess great minds think alike. Your guitar looks great!

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

The Effects of Coffee, in a good way, folks........

Started by BrianQ.. Last reply by Wilda Connell Aug 5, 2020. 7 Replies

Low Budget Sanding Tool

Started by BrianQ.. Last reply by Order99 Jun 9, 2020. 3 Replies

Nails for frets?

Started by Mike. Last reply by Alan Robinson Aug 1, 2017. 8 Replies

Flea market finds

Started by Mike Jul 24, 2017. 0 Replies

Not just a lolly stick

Started by Wade Jan 2, 2015. 0 Replies

Save that box screw up!

Started by Wade. Last reply by Thomas "Duck" Petry Dec 3, 2014. 2 Replies

CB string height gauge

Started by Wade. Last reply by Wade Jul 9, 2014. 2 Replies

Recycled stuff

Started by Keith 66 Jun 11, 2014. 0 Replies

Free recycled Piezo pickups

Started by Wade. Last reply by Rob Brighton Jul 2, 2013. 19 Replies

Joining Lumber

Started by Where's Uranus?. Last reply by Mark Lindsay Jun 4, 2013. 8 Replies

Fretboard radius

Started by Wade. Last reply by rusty case Feb 11, 2013. 1 Reply

Free grounding foil

Started by Wade Feb 10, 2013. 0 Replies

Free Fret dot markers

Started by Wade. Last reply by Mark Lindsay Feb 3, 2013. 23 Replies

Recycled tonewood

Started by rusty case. Last reply by rusty case Nov 21, 2012. 13 Replies

Low $ substitute for banjo face?

Started by rusty case. Last reply by rusty case Nov 18, 2012. 6 Replies

Cheapo strings

Started by Karl G. Siewert. Last reply by rusty case Aug 27, 2012. 4 Replies

Hand saw.

Started by Wade. Last reply by rusty case Aug 27, 2012. 2 Replies

Tennis, anyone?

Started by Order99. Last reply by Order99 Aug 17, 2012. 4 Replies

1/2 Priced Nuts and Saddles

Started by Claude. Last reply by Order99 Apr 8, 2012. 10 Replies

Latest Activity

Doug Thorsvik posted a video

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 195th Zoom Mtg 03/25/24. Only 1-finger chords, free songbooks here: https://www.cbgslinger.com/download CBG SOF Songbook...
43 minutes ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
17 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
17 hours ago
Kent Thurston updated their profile
18 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
18 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
18 hours ago
Poorness Studios liked A.D.EKER's video
20 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
21 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
23 hours ago
A.D.EKER commented on A.D.EKER's video
yesterday
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
yesterday
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->