Doug Thorsvik's Comments

Comment Wall (104 comments)

You need to be a member of Cigar Box Nation to add comments!

Join Cigar Box Nation

At 7:37am on February 12, 2024, BrianQ. said…

Hey Doug, it is possible to make a passive octave pedal from a pickup & some diodes, but it will be randomly fuzzy & glitchy without any warning. A polyphonic octave pedal is what you want, but the downside to octave pedals is their high pricing? Mooer makes some economical pedals like the pure octave,tender octave & purer octave witch all do a clean  low & high octave effect for under $100, most others are $200+ Cheers:)

At 6:26am on January 1, 2024, Chance said…

Doug, You are right, about ending up with a bunch of lefty builds prototype/experiments. I just hold on to them and play them every now and then, I just cannot bear to strip them for parts. Eventually I will find other lefties to gift them to.

Honestly, all of what I know about build CBG's I learned primarily from Shane Speal, Uncle Crow, John "RedDog" McNair, and Chickenbone John, and I picked things from each of these prolific builders to incorporate into my builds. Each of these have somewhat different styles/approach, but the end result is the same: a fine sounding CBG.

Cheers, and a have a stellar new year.

At 5:07pm on November 29, 2023, Chance said…

I should have mentioned string tree's, in that, if you utilize them careful consideration of place will better allow the git to be used R or L.  Cheers.

At 4:47pm on November 29, 2023, Chance said…

HiGreeting Doug,

Better late response than never.  First, off all of my builds are fretless and most utilize a rod piezo with a preamp.  If the sides of the box are too thin for the preamp, I will use the smaller passive, slider type volume and tone controls.  If the box is thinner than that I generally will not use it, but if I do use it I will direct wire the pickup to the jack.  If the box is deep enough I will place the preamp underneath the neck on either a stick-thru or stick on top.  I will only put volume and tone control pots on the soundboard, if the git will be dedicated right or left.This frees up sides to be lefty or righty.  The tuner placement generally makes no difference.  The jack and jack plate should be as close to center near where the neck protrudes, or terminates inside or on top of box.  The jack/jack plate are only mounted on soundboard if the git is dedicated right or left hand play.  Fret mark's on the neck/fretboard are at least marked on both sides, I do not always mark the fretboard side (under the string).  Sometimes the artwork on the box lid will be upside down when strings are switched from right handed play to lefty, or vice-versa, but "So What!"  Stick on top builds I will generally use the thinner bottom of the box anyway.  Really that is all I do to make the git playable by both lefties and righties.  Cheers.

At 10:25am on November 10, 2023, Slow Mick said…

Thank you for this very valuable help!

Best regards.

At 9:05pm on September 26, 2023, Pieter Albertyn said…

Doug. My plan is to build a few CBGs over the next week or three. Well, at least to the point where the "ugly stuff" has been dealt with. (Sawdust, table saws, routers, shaping and sanding.) I am forced to do batch processing of components like necks and bodies so I can complete similar processes in one go. It is not ideal, as I prefer to work on an instrument as a bespoke unit. Will see how it goes and will feed back as I go. With any luck at all I will produce those photos you asked for along the way. Regards. Pieter.

At 12:38am on September 23, 2023, Michael Fred Johnson said…

Thanks for the comments Doug

At 10:59pm on September 22, 2023, Pieter Albertyn said…

Doug. I refer to your request for photos. My circumstances are such that I had not been able to build since I produced a number of mini guitars for my grandkids. (Doing so created an awful mess and caused much discomfort for my wife ) I now plan to attend a newly established "Menzshed" in our local town. They provide work space and basic equipment for DIY'ers at a facility in town. I am making slow progress and will feed back once I have something to show. All of the best. Pieter.

At 12:08am on June 11, 2023, A.D.EKER said…

No Doug ! No Modesty !the way you operate, whit the 3D printing, Style,Songbook ,One vinger Program, Your zoommm Classes, and your live Shows,You are one Original C omputer G enerated,C igar B ox G uitar Builder, nothing but admiration ! To You Doug ! Hats Off ,and why Not ? hard work diserves a thumbs up and a pat on the Back! 

At 11:34pm on June 9, 2023, A.D.EKER said…

BY the Look of it ,You are ready for Masse Scale Production ! there Doug, adapt the color and Go !  frenchize Whit Gitty and BOOOOOM ! Millionaair in No time ! The Future Of  CGCBG is on our Doorstep !! Good Luck Bud !

At 8:31pm on May 21, 2023, A.D.EKER said…

a fine tune Doug ! back there for a minit Thanks .

At 5:50pm on March 31, 2023, BrianQ. said…

Hope to see the slinger’s doing their thing :)

https://www.cigarboxnation.com/events/callyfest-2023

At 3:44am on August 21, 2022, Robert Neal said…

Thank you for the friend request ( my first) I am sorry it took so long for the reply. I will start being more active sometime next week. Thank You again

At 1:16pm on November 30, 2021, Rope Walker Country Star said…
Thanks for checking in DougThorsvik. I guess I got in a little CBG funk around the time of DaveLynas passing, and got a bit busy with other stuff too. I trust you’re still slingin’ the hits and the two string wonders!
At 2:17pm on August 21, 2021, 3 String Blues said…

you are a wonderful person Doug!

At 12:49am on August 14, 2021, Martin said…

Hi Doug, thank you so much for the songbook. Great stuff man!!!

Cheers,

Martin

At 7:11am on August 12, 2021, Paul L. Hanz said…

Thanks Doug for the Awesome Song Book! Very well done, and greatly appreciated. This just mightt be a way to attract more newbies into the grand art of CBGs.

At 7:21am on August 11, 2021, Bill Tankersley said…

Thank you for the great songbook!

At 3:09am on August 11, 2021, Mike Willmouth said…

Thanks Doug for sharing your songbook.  It's fantastic! 

At 6:38pm on August 10, 2021, silvernitrate said…
Thanks Doug - very nicely done and a great collection.

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray on Thursday. 2 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by A.D.EKER Jan 29. 3 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

HELP !! IN VERMONT.

Started by Ranblin' Dan Stevens in Other stuff - off topic, fun stuff, whatever. Last reply by Patrick Kelly Jan 21. 7 Replies

Fat Back Neck

Started by Jim Booth in Building Secrets, Tips, Advice, Discussion. Last reply by Jim Booth Dec 15, 2023. 7 Replies

Brick House CBG

Started by Ian Boyd in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Dec 13, 2023. 3 Replies

Best power tool for building?

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Dec 11, 2023. 10 Replies

Latest Activity

smilingdog1 liked Cigar Box Nation's video
13 minutes ago
smilingdog1 liked Steve Holladay's video
15 minutes ago
smilingdog1 liked Uncle Toad's video
16 minutes ago
3 String Blues posted a video

Dog House Blues - testing out a Line 6 Catalyst Amplifier

bought this sweet sounding amp on Amazon....my first quick test recording on a 3 sting cigar box guitar...the reverbs onboard this thing are just fantastic!!...
3 hours ago
BrianQ. commented on AGP #'s photo
Thumbnail

AGP #523 -''Clean Machine''

"Covering a metal covered pickup with more metal will give unwanted eddy currents? I would’ve…"
12 hours ago
AGP # liked CaptnCatfish's video
13 hours ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #523 -''Clean Machine''

""Thanks A.D.", Yep!, sometimes things don't go quite as planned, but there's…"
13 hours ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #523 -''Clean Machine''

""Thanks UJ", the Round Soundhole was the result of the failed Ghosted Pomade Tin effort,…"
13 hours ago
Uncle Toad commented on Uncle Toad's video
Thumbnail

Gotham epoxied-in rod piezo demo - no squeeze

"Wooden box - if you see the Gotham Guts photos, you can see the severely hacked away back and…"
13 hours ago
Uncle Toad commented on Uncle Toad's video
13 hours ago
AGP # commented on AGP #'s photo
Thumbnail

AGP #523 -''Clean Machine''

""Yes BQ", Horrible Feedback Noises when using the Distorted Amp Settings, and a very…"
13 hours ago
Uncle Toad commented on Uncle Toad's video
Thumbnail

Gotham Sound Check

"Poorness Studios- I am not a pro at soldering… it took hours, and one of the three way…"
13 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->