Hi,

Are there any tricks to stringing up a new CBG? I just broke a string and not sure if it matters as to which side of the tuner to slide the string through.

Views: 302

Replies to This Discussion

I am purely a novice, but I think it doesn't matter which way you thread the tuner. I think the convention is to turn the tuner handle away from you i.e. counter clockwise on the D and G strings and clockwise on the single tuner (g) on the lower side of the head., so thread the string so they progresses smoothly around the spindle. I use an electronic tuner. Even though be prepared for broken strings,’ I have tuned my CBG to open G i.e. GDg. Just remember that strings are available from "Gitty" in packs of 3, one each GDg. you can get bulk buy of 12 packets landed in Australia for about $ 35.

Thanks Redbelly,

The strings from Gitty seems a whole lot thinner then ones I see on a regular acoustic six string guitar. What if I use strings from a regular acoustic six string ?

I have used both but I am not "advanced" eneough to judge The "Gitty strings are "Acoustic Medium Low ppen G'Blues Blaster; G D g. String size .044W,.034 W,& .026W

 The ones that came with the CBG kit from Gitty was .026W . .017P, .013P.

I will get a set of strings you mentioned and see how it goes.

Thanks

Don't think it matters which side you run the string thru.

Might try hitting the string before you turn the tuner knob, I heard once that if you turn the tuner while the string is ringing, it helps to keep it from breaking.

I don't know if it really helps, but that's the way I do it for my banjo and uke

Hi Paul,

The only tip I have to offer is to make sure you wrap the string once or twice completely around the shaft of the tuner before you thread the string through the hole in the shaft of the tuner. This will releave some of the string tension at the point where the string goes through the hole in the shaft. The edge of the hole is rather sharp and under a lot of string pressure acts a bit like a knife (at least I imagine so). I seem to have less string breakage after I started to wrap them one time around the shaft before inserting the string in the hole. Wrapping twice around may even be better, but I haven't found the need to go to that much trouble.

-Rand.

The side that you put the string through will determine which way you turn the peg to tune up or down. Pegs on the bottom turn clockwise to tune up so thread the string through from the top/inside. if the peg is on top it will turn anticlockwise so the string should go through from the bottom/inside. Threading it through from the inside reduces the angle of the string at the nut.

Breaking strings is usually about too much tension by winding it up too tight. Light strings break easier than heavy ones so guage is important, you've really got to push anything thicker than a .17 pretty hard to break it. 

For sliding, an unwound string on the top, that is closest to the ground but with the highest pitch, will give you a brighter sound than a wound string. Having said that heavy strings work better for slide but put more tension on your neck. I recently restrung mine with an unwound .21 on top, a .38 in the middle and a .47 on the bottom. This tunes them up nice and tight in G and I could easily go back to E if necessary. My guitar would take the extra tension to go to A but I wouldn't leave it there for long. For an acoustic sound, and if you're mainly playing chords, I'd go lighter than this.

All these guitars are different though and you'd need a good strong construction to take this much pressure so if you're not sure just take it easy and experiment. If you're neck starts to bow then back off the tension on the string.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Can a box be too shallow?

Started by Sean Murphy. Last reply by Raymond Grimmitt Dec 21, 2021. 3 Replies

Removing box labels

Started by Robert Dawkins. Last reply by Order99 Jul 6, 2020. 8 Replies

Build 2!

Started by Sean Murphy. Last reply by Sean Murphy Oct 28, 2018. 3 Replies

Best/"Easiest " Way to notch out CBG Neck......?????

Started by Brian M Nusser. Last reply by ChickenboneJohn Nov 14, 2017. 16 Replies

First build, not-great results

Started by Sean Murphy. Last reply by Slow Blues Dani & Ol' Grey Bear Nov 14, 2017. 3 Replies

Neck length

Started by Holly Hodson. Last reply by Thomas "Duck" Petry Nov 9, 2017. 4 Replies

"If you wand to get something done real bad . . ."

Started by Michael Zimmerle. Last reply by Richard Dean Oct 23, 2017. 2 Replies

First build and a broken string.

Started by Dan Mullen. Last reply by Richard Dean Oct 23, 2017. 8 Replies

What type of saw to use?

Started by Anne M. Fridley-Owen. Last reply by Anne M. Fridley-Owen Dec 4, 2016. 3 Replies

*()@%&$! Piezo

Started by Chance. Last reply by Chance Oct 24, 2016. 3 Replies

general

Started by tommy farrar. Last reply by tommy farrar Nov 28, 2015. 2 Replies

Tail - or where the strings are mounted

Started by evanmars. Last reply by Richey Kay Aug 25, 2015. 7 Replies

My fifth build

Started by James A OBrien Apr 7, 2015. 0 Replies

Cardboard Cigar Box

Started by Redbelly. Last reply by Thomas "Duck" Petry Jun 30, 2014. 3 Replies

Just Finished My First CBG. YAY!!!!!!!!!!!!!!!!! (The Sequel)

Started by L. W. Carlson. Last reply by Thomas "Duck" Petry Jun 27, 2014. 3 Replies

Scale Length

Started by Wagner Richter. Last reply by Wagner Richter May 7, 2014. 3 Replies

Connecting a Neck

Started by Thumper Apr 18, 2014. 0 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->