OK, I got a wild hair and wound my first pickup last night.  It works...not real loud, since the smallest wire I had on hand was 34 gauge, but still not bad.  It is a short fat little guy and I like the tone...it tames the highs quite well in comparison to a piezo.  A little 2 transistor preamp, and it will be fine.

Anyway, I have obtained a black Cohiba box I want to do my first 4 stringer with, and I want to use the pickup in it.  (I built the pickup with 4 poles just for this guitar)

I know that there will be a little more neck stress with 4 strings, and I am wondering about neck strength.  This will be a neck thru build, but what will I need to do to brace the neck to make up for where I will need to relieve it for the pickup?  Will adding a "doubler" brace under the neck be enough, or will I need to add "wings" as well?

The neck will be red oak, fretted  (no separate fretboard, unless that is the best way to retain strength), and I would like to shape the neck a little as well, to make it easier to play.

I don't want to bow the neck with the added tension of the 4th string and the relief cut for the pickup.  As far as the pickup position, I am thinking I want it at the base of the neck or relatively close to there, for a more mellow sound.  I also would like to relieve the neck under the lid, like I have done my prior builds for a decent unplugged sound, unless that is asking to much as far as strength goes.

Thanks in advance, guys!!

Views: 332

Replies to This Discussion

You should be ok but I would double up on the neck under the lid. See my pics on my page for more info on that. Message me if you have questions. I did the same on a Cohiba box 'sept the neck is poplar. I did note that the recessed area for the pickup (I assume you mean mag pup) did weaken the neck and some bowing did occur but I added more reinforcement and it works good now. You might want to consider a laminated neck. I can explain that too.

If you are going to make it an all elec (not acoustic at all) I would fill the box with plywood or pressboard with routed areas for the pup, knobs, wiring. You can make a thru neck if you want or 'bolt on'. My dream 6-string will be 'solid' with a bolt on neck.

If your strings are .010 -.026s your neck should be okay tension wise. I have always doubled up the neck in the box, just in case. Notch out the neck where the pickup will be placed and glue another piece of Oak, or whatever, beneath it for strength. If you can get the pick up in the area of where the 24th fret would be you pick up some of the string harmonics. adds to the sound. Adding a fret board, even 1/8" to 3/32" will help strengthen the neck. If I'm shaping the neck a lot and taking away a bit of the bottom of the neck I tend to add a fret board just to be on the safe side.
Thanks, guys...I will try to get the pickup in the area of the 24th fret, and I will brace the fool outta the box...This is a thinner Cohiba, so I am thinking hard about doing like you suggested, Wes, and making it a "solid" body, since the box is shallow (1 1/4" deep with the lid closed..) That might be my only choice, seeing as the pickup is 5/8" thick....If I made it into a solid body, that should give me some strength so I won't have to worry.. If I go that route and make it a "pure" electric, I will prolly sting it with .009's since thats what I use on my Strat.

Thanks for the suggestions, guys!!
hey Tim,
Build the neck like I did the Mac that Chris bought. I just added a full thickness piece of scrap That I cut off of the too long neck blank. But instead of making just as long as the lid relief, I left it long in the front and shaped it into a heel.

You may need to add "wings" just to have something to ount the pick-up to, depending on the width.

btw- I scored a couple of Cohibas myself. A black Supremo and a natural Crystal Corona.


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources

Discussion Forum

Using & Making Templates

Started by John Sims. Last reply by BrianQ. Sep 5, 2018. 4 Replies


Started by BP - RabidSalad - Aug 15, 2015. 0 Replies

A Simple Fret Scale Ruler

Started by John Sims. Last reply by Brown Water Jerry (Rice) Jun 30, 2015. 7 Replies

fret construction

Started by Allan. Last reply by Monterey Jun 28, 2015. 8 Replies

Milk Paint & Natural Pigments

Started by Monterey Jun 28, 2015. 0 Replies

Homemade Wood Stains

Started by Wes "I'm Baaaaack" Yates. Last reply by Monterey Jun 28, 2015. 22 Replies

Custom Made Logo Decals

Started by John Sims. Last reply by Monterey Jun 28, 2015. 11 Replies

Holding down fretboards for gluing

Started by Wes "I'm Baaaaack" Yates. Last reply by Joe Caruso Apr 12, 2015. 9 Replies

Simple Fret Depth Gauge

Started by John Sims. Last reply by Joe Caruso Apr 12, 2015. 3 Replies

Easy way to glue down a fret board without it sliding

Started by John Rivers. Last reply by Steve Walker Mar 18, 2014. 1 Reply

Sharpie safe varnish for saving signatures on CBGs

Started by Wes "I'm Baaaaack" Yates. Last reply by Wes "I'm Baaaaack" Yates Jan 2, 2013. 4 Replies

Strap buttons on the cheap

Started by Wes "I'm Baaaaack" Yates. Last reply by jamie bark Aug 10, 2012. 16 Replies

Side markers on the REAL cheap!

Started by Wes "I'm Baaaaack" Yates. Last reply by Soul Cat Guitar Uke and Amp Nov 28, 2011. 10 Replies

Homemade Dot Fret Markers

Started by Jerry. Last reply by Jerry Oct 26, 2011. 5 Replies

Fretboard radius sander on the cheap

Started by Wes "I'm Baaaaack" Yates. Last reply by Wes "I'm Baaaaack" Yates Jul 14, 2011. 12 Replies

35mm metal slide storage box

Started by nick tyson. Last reply by nick tyson Jul 7, 2010. 2 Replies

questions about installing a pickup

Started by Hey, TURN IT DOWN!. Last reply by Outhouse Instruments May 30, 2010. 4 Replies

Dent removal

Started by Wes "I'm Baaaaack" Yates. Last reply by Phil Delpierre May 19, 2010. 2 Replies

Stains for wood

Started by Robert Hynden. Last reply by Robert Hynden Apr 13, 2010. 2 Replies

Latest Activity

Richard Sundberg commented on Glenn Kaiser's video

MARCH 2023 Canjo

"I enjoyed that! Simple and effective. Is it soup."
1 hour ago
Richard Sundberg commented on 3 String Blues's video
1 hour ago
Richard Sundberg commented on A.D.EKER's photo

cant hardly wait callyfest

"Good news! Just received the liquor license for CallyFest! On short notice. Cheers!"
1 hour ago
Richard Sundberg commented on A.D.EKER's photo

cant hardly wait callyfest

"I’m glad to announce tickets sales are going well. When you see scalpers selling tickets in…"
1 hour ago
Richard Sundberg commented on A.D.EKER's photo

cant hardly wait callyfest

"Hi A. D. Good news! Power went out because of storms here, but it’s back on. It got tense,…"
1 hour ago
Scott Schoepf liked BrianQ.'s photo
4 hours ago
Derek Robertson commented on Derek Robertson's photo


"Iive been sitting on this box for a few years just got round to it.thanks for your interest."
9 hours ago
AGP # commented on AGP #'s photo

AGP #493 - ''Juzzie''

"Juzzie Smith Bamboo Lap Slide"
12 hours ago
AGP # posted photos
12 hours ago
Doug Thorsvik commented on Richard Sundberg's video

Going Down To CALLYFEST. A. D. Eker

"The ball is rolling now!!! See y’all at Califest."
14 hours ago
Doug Thorsvik commented on James O Lunsford's video

Going to Cally Fest

"Very creative James O! See you there."
14 hours ago
James O Lunsford liked Calvin Fowler's photo
14 hours ago


© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->