Making and Installing Position Markers for Your Guitar - by Brian Johnson edited by Dragon

Here's a simple and economical way to make fret position markers with little chance of destroying you work. I am sure that someone else has probably done this before, but since I haven't seen it yet, I will offer it to you hoping that you can use it on one of your projects.

All you need to get started is a 1/4" flat head screwdriver, a drill with a 1/4" drill bit or 1/4" router bit (I use a dremel 1/4" router bit and dremel router plunge base with an edge guide attachment), a 1/4" hand held hole punch (like kids use in school for their paper), and a handful of medium or heavy guitar picks in whatever color(s) that suits your project. I like heavy picks the best since it makes for easier installation with less mistakes in case you drill too deep...

Start by simply punching holes in the guitar picks with the hole puncher. You should be able to get at least nine or ten fret markers from each pick. I have had no problem at all punching heavy guage picks with a kids hand held school paper punch, but that isn't to say you could not use lighter gauges if you desire. The thickness of a heavy guage pick allows more room for error when drilling or routing the holes in the neck or fret board, and you can't see through them if sanded down too much.

Take your drill or router using very high speed so as not to chip the edges of the hole (if using a drill bit, use a chisel point bit!), and s-l-o-w-l-y drill a small indention in the fretboard where you want the marker to go (hopefully you have already laid that out on the board). You do NOT have to drill very deep. Just drill to the thickness of the pick or slightly less. You can always double stack the pick dots so they are thicker if you drill too deep.You can always check the thickness and depth, and drill deeper. I allow a bit of the dot to stay above the fretboard since it can be sanded down flush.

Once the hole is deep enough, take your screwdriver and gently clean out the hole so the marker will sit flush (if required). Using whatever adhesive you like (I use super glue gel), place the marker in the hole. The fit should be snug enough that you will have to use the handle of the screwdriver to press the marker into place.

That's it.

Sand flush to the fretboard surface if required and make sure the dots are drilled exactly between the frets by marking the with an 'X' from the corner edges of the fret, and make sure that the hole marks are perfectly centered before drilling. An edge attachment on a router base works great for me for getting the dots entered on the width dimension of the neck.

Experiment on scraps first! Here is a neck I did using 'pearl' type Fender heavy picks since it complimented the Macanudo box on this particular CBG. I have used evey color imaginable. I like the pearl type, white, abalone, gray, etc...

Practice neck with hole puncher, abalone, pearl and grey pearl picks

Router plunger base (for Dremel) with edge attachment

Views: 943

Replies to This Discussion

I've got some credit cards I'd like to use for this fret marker project!
Would a Forstner bit be even better for the holes? If I'm not mistaken, they're designed to cut nice, clean holes.

Yes they will work and yes you can get them very small.  Nice thing to is the flat bottom they leave.  You'll want to use a drill press tho so that you can control wander and depth. 

I use a Forstner bit in a drill press- set the depth so it's the thickness of the fret dot - very little - fret dot is made with a 1/4 inch hole punch that I've inserted into the drill press and cut out of guitar picks - glue them in and have never had a problem - working on number 6 now
I suppose, if you can find a small enough one! Let us know how they work out if you indeed use one...

That is super nifty... and answer the need in the midnight hour... if you know what I mean...

the best,



The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources

Discussion Forum

Using & Making Templates

Started by John Sims. Last reply by BrianQ. Sep 5, 2018. 4 Replies


Started by BP - RabidSalad - Aug 15, 2015. 0 Replies

A Simple Fret Scale Ruler

Started by John Sims. Last reply by Brown Water Jerry (Rice) Jun 30, 2015. 7 Replies

fret construction

Started by Allan. Last reply by Monterey Jun 28, 2015. 8 Replies

Milk Paint & Natural Pigments

Started by Monterey Jun 28, 2015. 0 Replies

Homemade Wood Stains

Started by Wes "I'm Baaaaack" Yates. Last reply by Monterey Jun 28, 2015. 22 Replies

Custom Made Logo Decals

Started by John Sims. Last reply by Monterey Jun 28, 2015. 11 Replies

Holding down fretboards for gluing

Started by Wes "I'm Baaaaack" Yates. Last reply by Joe Caruso Apr 12, 2015. 9 Replies

Simple Fret Depth Gauge

Started by John Sims. Last reply by Joe Caruso Apr 12, 2015. 3 Replies

Easy way to glue down a fret board without it sliding

Started by John Rivers. Last reply by Steve Walker Mar 18, 2014. 1 Reply

Sharpie safe varnish for saving signatures on CBGs

Started by Wes "I'm Baaaaack" Yates. Last reply by Wes "I'm Baaaaack" Yates Jan 2, 2013. 4 Replies

Strap buttons on the cheap

Started by Wes "I'm Baaaaack" Yates. Last reply by jamie bark Aug 10, 2012. 16 Replies

Side markers on the REAL cheap!

Started by Wes "I'm Baaaaack" Yates. Last reply by Soul Cat Guitar Uke and Amp Nov 28, 2011. 10 Replies

Homemade Dot Fret Markers

Started by Jerry. Last reply by Jerry Oct 26, 2011. 5 Replies

Fretboard radius sander on the cheap

Started by Wes "I'm Baaaaack" Yates. Last reply by Wes "I'm Baaaaack" Yates Jul 14, 2011. 12 Replies

35mm metal slide storage box

Started by nick tyson. Last reply by nick tyson Jul 7, 2010. 2 Replies

questions about installing a pickup

Started by Hey, TURN IT DOWN!. Last reply by Outhouse Instruments May 30, 2010. 4 Replies

Dent removal

Started by Wes "I'm Baaaaack" Yates. Last reply by Phil Delpierre May 19, 2010. 2 Replies

Stains for wood

Started by Robert Hynden. Last reply by Robert Hynden Apr 13, 2010. 2 Replies

Blog Posts

A Tribute

Posted by Ghostbuttons on January 15, 2023 at 12:00pm 1 Comment

Let’s talk Aeolian…

Posted by BrianQ. on August 26, 2022 at 5:05pm 0 Comments

Latest Activity

A.D.EKER commented on A.D.EKER's video

How Are You BCB 2023

"Well thank you Doug ! verry kind of you to say so ! glad you liked it !"
41 minutes ago
Robert Compton commented on Robert Compton's photo


"Thanks for the kind words!"
57 minutes ago
Robert Compton commented on Robert Compton's photo


"Thank you sir!"
59 minutes ago
Robert Compton commented on Robert Compton's photo


"Thank you so much everyone!...thats Hudson, he always gets to play the new one's first, before…"
1 hour ago
Robert Compton commented on Robert Compton's photo


"Thank you so much for the kind words! brand new to the site so im still tryin to figure out…"
1 hour ago
RON NORTHCUTT posted photos
1 hour ago
Doug Thorsvik commented on Poorness Studios's video

The Brady Bunch Theme Song (a musical skit w/CBG & kazoo)

"Fun! Fun! Fun! Very entertaining Kale. My wife and I enjoyed it.  A much better version than…"
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's video

Bridge Over Troubled Water: 2-String Surf Chugger Cigar Box Guitar

"I agree Uncle John! The first few lines in each verse were challenging to sing as they presented…"
2 hours ago
Poorness Studios posted videos
2 hours ago
Uncle John commented on Uncle John's video

Highway 61 Blues - recent relic build demo

"I. just went back and listened to one of your videos, Ron.  You do fine.  Thank you,…"
3 hours ago
Uncle John commented on Brian's photo


"Very nice.  Looks like a keeper."
3 hours ago
Uncle John commented on Brian's photo


"Nice git and strap!"
3 hours ago


© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->