Reworked Version w/ upgraded Power switching:

Views: 1023

Replies to This Discussion

Just found a stash of LM386N-3’s, happy amp building :)

Any ideas where I can find some N-3s?

 Cooool. In other news... What do you think of the NTE823?

It’s a surplus version of an LM386N-1, basically a recategorized chip, that’s slipped from its original specs? I don’t buy NTE components simply because they’re surplus, and they charge a premium price? surplus parts are usually stuff that has been sitting around somewhere wasting away or didn’t match original build specs? BTW, only 125-250mW, less than half a watt, so not the best for driving a speaker?

Grrreeeeaaaaaaaaatt. I bought a half-dozen of them for about $3 each from a local electronics store. Bear in mind I live in the most expensive dump of a town I've ever experienced.

 I read somewhere that it was good for a watt. Oh well. Just another nail in my enthusiasm for my new-found hobby. (Quite possible to soon my former hobby...) This is eating my lunch. I'm pretty good at larger soldering but this is killing me. I built one good one that sounded pretty decent until I messed it up installing it in the cabinet. Tried two more. Nothing. I think I have made every single mistake possible in this in spite of being very careful and studying this maddening activity in depth and in spite of all the great help from all of you. I still suck at this. Grrrr.

You could always bridge two of them to double the power? Or use them for a distortion box. I always try to check for specs online real quick to make sure it’s something I can use? I’ve bought many useless amp tubes & so forth.  Using the right solder tip, coupled with the right heat is ideal, but solder bridges happen so easily & most of the time not recognized by the naked eye, but it’s usually touching something it shouldn’t or not touching something it should. Just take your time & double check your work as you go. I’ve had many dead circuits before getting it right.

 Thank you Brian. I guess you are probably right about the solder bridges. My soldering leaves a lot to be desired. My tip may be a bit too big as well, but then again, I took the same guy's advise on this iron...



Thank you Brian. I looked at that data sheet you showed today.  I told the guy at the electronics shop that I wanted some LM386 N3s and he gave me these saying they were the same. I trusted him as he seemed to know what he was doing. He is the owner after all. I should have stuck with my theory: Owners and managers are usually the most clueless of workers in stores nowadays. I did see the 1 watt reference SOMEWHERE, might have been the little baggies they came in, but I know I saw it. 

 My main problem seems to be getting the solder to stick to the copper on the veroboard/stripboard. Any ideas?

Thanks again

 I finally took a picture of the package of the NTE823. Can you tell me what the 1W indicates? I am trying to get my head around this, I've never been a quitter, but I have just about given up on this hobby. I've spent too much money, built one good, working amp out of at least six tries and destroyed it trying to install it into a cabinet. I don't mean to be a wanker, but I've never had this much trouble learning and doing anything before.

 Wheeze... (Cocking head to side in defiance) Alright! Tomorrow is another day... I WILL do this!

Yes, it does say 1 watt, however the Datasheet from NTE site says it’s only rated 250-325mw? NTE is well known for its inconsistent info BTW? But at any rate, it doesn’t matter what the wattage, it can be used to make an amp? Maybe you should purchase a Solderless Breadboard until you can develop your soldering skills? Stripboard & a Breadboard are layed out the same, so the layout would work? You’re not the first to come up with zilch, I wired half stuff backwards & had horrible solder globs on my first pedals/amps? 

 Thank you for the info and more importantly, the encouragement! I have rebuilt motorcycle racing engines. I have rebuilt Mopar engines.  I have built parts that are in space. I have built medical parts that are in some people's brains, but I can't do this? Yeh, I can do this. I just need to stop being a wanker.

 Thank you Brian!

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Discussion Forum

LM386 Amp w/ Switchable Clean Channel

Started by BrianQ.. Last reply by BrianQ. May 28, 2021. 1 Reply

Simple 1st Timer CBG Amp

Started by BrianQ.. Last reply by BrianQ. Sep 28, 2020. 25 Replies

Matching Speakers to LM386

Started by Southern Ray. Last reply by Southern Ray Aug 6, 2020. 11 Replies

Suggestions wanted for easy amp build

Started by Southern Ray. Last reply by Southern Ray Jun 16, 2020. 11 Replies

Ruby Amp

Started by BrianQ.. Last reply by Southern Ray May 17, 2020. 27 Replies

Low-Z pickup and components values

Started by Southern Ray. Last reply by Southern Ray May 13, 2020. 6 Replies

Oops

Started by Southern Ray. Last reply by Southern Ray May 3, 2020. 12 Replies

DIY Spring Reverb

Started by Kevin Keating. Last reply by Paul Craig Oct 17, 2019. 4 Replies

TDA2030A Amp

Started by Bama Hound. Last reply by Gary Stenzel Jul 23, 2017. 14 Replies

Home Brew Champ Tube Amp

Started by Scott aka Farmer Ted. Last reply by Paul Craig Feb 6, 2017. 3 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Jan 27, 2017. 29 Replies

5 Watt Amp Kit (DIY Case)

Started by Walter Haapapuro. Last reply by Gene Jones Dec 7, 2016. 46 Replies

DIY reverb behold - I found this online

Started by Danny B.. Last reply by Paul Craig Nov 2, 2016. 3 Replies

Bass Cabinet project

Started by Murdoc_420. Last reply by Murdoc_420 Jul 16, 2016. 34 Replies

Kalamazoo Model 1 Deluxe

Started by Scott aka Farmer Ted. Last reply by Rick Alexander Jun 20, 2016. 12 Replies

LM386 amp and other stuff

Started by Denis U. Last reply by Denis U May 29, 2016. 19 Replies

Combo Amp Build

Started by Paul Craig. Last reply by Paul Craig May 27, 2016. 113 Replies

Latest Activity

Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

The Slingers

"You could be right Uncle John! I decided we needed a picture of the group and my brother was able…"
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Sixteen Tons: 3-String Surf SLG License Plate Guitar (Not a Cigar Box Guitar)

"I appreciate the good words AGP! I’m grateful for a group that continues to expand my musical…"
2 hours ago
W.M. Peterson commented on W.M. Peterson's video
Thumbnail

Shake that thing

"Thanks Uncle John for the nice comment "
3 hours ago
Poorness Studios posted a video

Sundown (low-budget cover on CBG & kazoo)

I decided to do a super "low-budget" performance this morning. This is the first time I've tried this particular song on 4-string CBG and kazoo so it's a lit...
3 hours ago
Uncle John commented on Doug Thorsvik's photo
Thumbnail

The Slingers

"This would be a good album cover,"
3 hours ago
Uncle John commented on W.M. Peterson's video
Thumbnail

Shake that thing

"Great to hear this one again.  Pretty true to the Oh-riginal.   Nice job, good hat…"
3 hours ago
W.M. Peterson liked Gary O'slide's video
5 hours ago
W.M. Peterson posted a video
5 hours ago
AGP # liked GARAGE HERMIT's photo
11 hours ago
AGP # liked Randy S. Bretz's photo
11 hours ago
AGP # liked Doug Thorsvik's photo
11 hours ago
AGP # commented on Doug Thorsvik's video
11 hours ago

Music

© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->