I'm a bit over the moon at the moment. I built a really simple LM386 amp, added a couple of <3inch full range speakers and housed it in an old watercolour paint box with a cigar box label and old computer fans protecting grills and it's magic.

Never satisfied, I added a switched output jack and ran the power through a stereo input jack so it only powers on with the lead inserted and I can play it through my home made cabinet with 2 1960's 12" Celestion Greenbacks. It roars - although there's more residual hum when I do that.

I've been using a Christmas present I gave myself - David Eric Nelson's book Junkyard Jam Band for circuits and ideas and also built his Mud'n'Sizzle preamp. The preamp seems to work really well at overdriving the 386 and I can get either a clean or deep and muddy overdrive. I just wish I could play !!

I want to be able to run the amp off a wall wart as well as battery, and I've got a socket for the 9v wallwart which seems to be switchable in that there are 3 connectors on it, one for the center +ve, and the other two which are connected then the wall wart isn't plugged in and not connected when it's not. Can I just  run the negative that the stereo input jack switches to those two terminals, so that then there's no wall wart, and the jacks in, I use battery power, and when the wall wart is connected, I use it instead? Is a little knowledge a dangerous thing, or am I onto a sane idea?



Views: 828

Replies to This Discussion

I have to admit I did feel a bit guilty about the lack of evidence. Will try to get some pictures taken over the weekend. Sound will take longer.

Thank you my conscience!!

This diagram shows how to wire up the wall wart jack. Take note of the stereo jack on the left, which is set up so battery power is only used when the guitar plugged in, and the wall wart is unplugged.

The V+ from the wall wart jack goes to the on/off switch on your amp.

The 2.1mm jack is designed/wired so that the red+ tab receiving the battery positive lead disconnects the battery when the wall wart plug is inserted. Also, the negative lead from the battery to the 2.1mm jack, and the ring of the stereo jack act as the "battery disconnect".

I wanted to go that route on my amp build but it wouldn't work with the power jack that I had. So i just used a 2-way toggle to switch between battery and walwart.

Walwarts are convenient and last all day compared to a battery, but some walwarts can cause noise in your amp if they have an internal problem or they're cheaply made.

Lets see some pics Dennis. 

True about wall wart noise. Best choice is a "fully regulated" wart, like those used with effects pedals, etc.

a "fully regulated" wart    Is there medication for that?

Thanks Scott. That's fantastic. Now I know how to wire the 3 pole double throw stomp box switches I got from ebay - which look just like the Stewmac one and feel really solid except I got 10 from China for less than the price of one from Stewmac and it was free postage and packing and arrived in the UK in 8 days.

What software did you use for that diagram? I really like it.

Thanks again


Just search "10PCS 9-Pin Stomp Foot Switch" there's a few of them. The one's I got are those with the blue body to the switch.

What I usually do is have a quick look at what other stuff each of the vendors have. Sometimes that swings me in to direction of one of them.

This one was  the guy with the speedy delivery to the UK, but that's not where you are, is it? When I ordered them, I thought he was the only one who had them, but not any more.

OK, so here are pictures of the amp.

And the Mud'n'Sizzle preamp.

I will try to get some audio, but it won't be soon


Nice amps. I've found that these little 386 chip amp sound great through big speakers. Made a Ruby amp and put it into a Behringer practice amp using it's 6" speaker. An built my own dual chip bridged amp with a 10" speaker. The bigger speakers move more air and they sound surprisingly good.

Thanks Paul,

What I love is the amp with the preamp through the 2*12 cabinet. The overdrive/distortion I get though the small speakers of the amp itself is OK, but through the larger speakers if sounds so good. It's really hard to believe it's just a 1/4 watt driving it.

The most powerful amp I have is a 5 watt tube Fender Champ clone that was heavily modified by someone who knows what he's doing (unlike me). I haven't tried the preamp through that yet. There's just so much to play with and explore.

I've also got a couple of Chinese 18watt power amps that I want to try. They are small enough to live in the same small tin box as the preamp, and I just love the bizarre idea of having an 18watt amp that can play clean or distorted in what's essentially an Altoids tin.

The trouble with doing this stuff in the summer is that there's so much to do in the garden, and "she who must be obeyed" has no idea of the power of addiction!!

My dual chip bridged amp has loads of distortion at 1watt . I can use it as a preamp with a old Radio Shack 20watt PA amp, but I need to get some new speakers for it.

Old PA amps can be found for cheap and make great power amps with the right preamp or pedals.


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources

Discussion Forum

Tribute amps I've built

Started by Tom Hoglund Nov 7, 2022. 0 Replies

LM386 Amp w/ Switchable Clean Channel

Started by BrianQ.. Last reply by BrianQ. May 28, 2021. 1 Reply

Simple 1st Timer CBG Amp

Started by BrianQ.. Last reply by BrianQ. Sep 27, 2020. 25 Replies

Matching Speakers to LM386

Started by Southern Ray. Last reply by Southern Ray Aug 6, 2020. 11 Replies

Suggestions wanted for easy amp build

Started by Southern Ray. Last reply by Southern Ray Jun 15, 2020. 11 Replies

Ruby Amp

Started by BrianQ.. Last reply by Southern Ray May 16, 2020. 27 Replies

Low-Z pickup and components values

Started by Southern Ray. Last reply by Southern Ray May 13, 2020. 6 Replies


Started by Southern Ray. Last reply by Southern Ray May 2, 2020. 12 Replies

DIY Spring Reverb

Started by Kevin Keating. Last reply by Paul Craig Oct 17, 2019. 4 Replies

TDA2030A Amp

Started by Bama Hound. Last reply by Gary Stenzel Jul 23, 2017. 14 Replies

Home Brew Champ Tube Amp

Started by Scott aka Farmer Ted. Last reply by Paul Craig Feb 6, 2017. 3 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Jan 26, 2017. 29 Replies

5 Watt Amp Kit (DIY Case)

Started by Walter Haapapuro. Last reply by Gene Jones Dec 7, 2016. 46 Replies

DIY reverb behold - I found this online

Started by Danny B.. Last reply by Paul Craig Nov 2, 2016. 3 Replies

Bass Cabinet project

Started by Murdoc_420. Last reply by Murdoc_420 Jul 15, 2016. 34 Replies

Kalamazoo Model 1 Deluxe

Started by Scott aka Farmer Ted. Last reply by Rick Alexander Jun 20, 2016. 12 Replies

LM386 amp and other stuff

Started by Denis U. Last reply by Denis U May 29, 2016. 19 Replies

Blog Posts

A Tribute

Posted by Ghostbuttons on January 15, 2023 at 12:00pm 1 Comment

Let’s talk Aeolian…

Posted by BrianQ. on August 26, 2022 at 5:05pm 0 Comments

Latest Activity

Uncle John commented on RON NORTHCUTT's photo

Multi-strummer build

"Wow.  Prodigious!"
1 hour ago
Uncle John commented on Doug Thorsvik's video

Sundown: 2-String Surf SLG License Plate Guitar (Not a Cigar Box Guitar)

"Those slingers are picking some great songs.   Excellent. Happy Ground hog day,…"
1 hour ago
Uncle John commented on A.D.EKER's video

FORD Hubcap slide BCB 2023

"That is SUCH a great looking guitar, Andries.  Whining, bluesy good play.  Happy…"
1 hour ago
BrianQ. commented on Fergus Lester's photo


"Ehh… if it’s wood & it’s a box, then it’s a cbg in spirit like the…"
10 hours ago
BrianQ. posted a status
"Don’t you hate it when you make a big order & forget one thing???"
10 hours ago
BrianQ. liked RON NORTHCUTT's photo
10 hours ago
BrianQ. liked RON NORTHCUTT's photo
10 hours ago
BrianQ. commented on RON NORTHCUTT's photo

Multi-strummer build

"I feel you with cigar boxes, since they’re never all the same size in an assortment, you have…"
10 hours ago
Doug Thorsvik commented on A.D.EKER's video

FORD Hubcap slide BCB 2023

"Slide on A.D. slide on. Raw and real!"
11 hours ago
Doug Thorsvik commented on RON NORTHCUTT's photo

Multi-strummer build

"Bring on the clones! Looking good Ron. Production runs can really save some time especially setup…"
11 hours ago
RON NORTHCUTT commented on RON NORTHCUTT's photo

Multi-strummer build

"This is the first time I have done a 6-unit production run and it is really speeding things up. I…"
15 hours ago
Paul Craig replied to Mark's discussion Affordable and easy designs for youth group
"I just used a 10 dollar wood and metal pencil box from Walgreens to make a guitar for my Grandson.…"
15 hours ago


© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->