Ok, so I built my first CBB, now I want a portable amp.

==Disclaimer: I have no idea what I'm doing!!! So any and all advice is greatly appreciated==

 I found a good box at the Cigar Shop recently: 16"x7x5

Thinking of mounting the speakers in the bottom, nice looking wood (thinner than top). Maybe a latch on the side panel to open for controls panel? Storage box for batteries, maybe ac adaptor? Picks, slides.

 I would like to have an AC DC adaptor, not sure what voltage. The amp says 9-15v, could I hook a wall adaptor and a 9v battery up to  switchable loop?


 I am thinking about using this amplifier:

Wayfinder reports good luck with it. Though it is volume only, no tone. Seems easy enough to plug speakers into it.

AC/DC 12V 2x15W Digital Quality Audio Amplifier DIY Kit Dual-Channel Module 4-8Ω

1. Working voltage: DC 9-15V
2. Power: 15W +15 W
3. Maximum power:30W+30W
4. Output Impedance: 4-8Ω


Would need to add a power switch between amp and supply.

  And looking at these speakers:

PYLE-PRO PDMW5 - 5'' High Performance Mid-Bass Woofer

  • 100 Watts RMS / 200 Watts Peak Power Handling - 5'' Treated Paper Cone
  • 1'' High Temperature Aluminum Voice Coil - 15 oz Magnet Structure
  • Sensitivity: 90dB - Frequency Response: 80Hz ~ 7kHz
  • Mounting Depth: 2''
  • 8 Ohm Impedance



 For power supply a 9v battery and a acdc jack would be sweet. Can't seem to find an adaptor line in jack that isn't for a specific computer


Ah, this might work?



 Power switch?:



 Maybe just a 9-volt battery that I unplug when not in use?

Views: 647

Replies to This Discussion

 Hmm, guess I can't edit original post.

 Here are images for the above items (links work too)

 Thanks Wayfinder, can't find the milli-hours. 

 Honestly would just as soon have wall jack as anything, don't want to waste batteries.

 That power port is a couple bucks, can't find any on wires.

These are 10 for $2


guess I could get a toggle at hardware store. Couldn't find much on ebay, maybe I'm searching wrong.

 We used to have a radio shack, it dried up. 

 This might work as battery? Rechargeable 12v.


 Could fit inside box if i only use one speaker. Probably has to remain upright?

Awesome thanks for the help. Should be able to build this for $50. Battery being most of that.

 Might just do one speaker so I can house the battery inside. That would give me about 4-5" for a control panel in between. (toggle/volume)

I built this a while back, awesome amp, but fairly expensive.


I have also had great luck using Danelectro Honeytone amps you can get on eBay with 9V adaptor for around 25$, they kick butt & are cheap. Check out my vid of my Dano driving a 4X12, super loud. If interested I'll tell you how to do it, EZPZ.


 Thanks, yeah that's a nice cab.

 The Dano would be cheaper but I'd look to do a more self built wood model. (Don't want to deal with that plastic housing-plastic is bad :D )

 I know I know, I'm still cheating by buying a premade amp and not wiring one up... Baby steps :)

 I just realized that this amp has an 1/8 jack output. I have a few 1/4 to 1/8 adapters so I guess I could situate it so the volume and toggle are inside the panel, and the 1/4 adapter would be on the front panel under the speaker.

You could remove the insides of Dano & mount to wood case, plus you have tone & gain controls. Have fun with project.

Yeah but then I have the new plastic box that will be here for a million years that I have nothing to do with besides throw it away :(

Be mindful of how you wire the walwart jack(center pole + or -) and make sure the walwart plug is the right orientation or you'll possibly toast your amp.

Have fun and take your time. Check everything twice.

 Alright: Parts ordered.

 That amp above (looks like 3-7 weeks for delivery) :(  $3

 One speaker above. $10 with shipping

 Cabelas 12v recharge battery. This has clamps on ends of wire, suppose they can just be cut off. $35 with charger cable.

 Toggle switch from True Value ($3 as opposed to waiting for $1 online)

 Wires from True Value (I think 14g) bulk red/black/green $3


 The wait begins.

Sure thing, I'll try and carry it through to the end and have photos at least.

 Enough to make it easy enough for someone else to duplicate. (if it works :)  )


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Tribute amps I've built

Started by Tom Hoglund Nov 7. 0 Replies

LM386 Amp w/ Switchable Clean Channel

Started by BrianQ.. Last reply by BrianQ. May 28, 2021. 1 Reply

Simple 1st Timer CBG Amp

Started by BrianQ.. Last reply by BrianQ. Sep 28, 2020. 25 Replies

Matching Speakers to LM386

Started by Southern Ray. Last reply by Southern Ray Aug 6, 2020. 11 Replies

Suggestions wanted for easy amp build

Started by Southern Ray. Last reply by Southern Ray Jun 16, 2020. 11 Replies

Ruby Amp

Started by BrianQ.. Last reply by Southern Ray May 17, 2020. 27 Replies

Low-Z pickup and components values

Started by Southern Ray. Last reply by Southern Ray May 13, 2020. 6 Replies


Started by Southern Ray. Last reply by Southern Ray May 3, 2020. 12 Replies

DIY Spring Reverb

Started by Kevin Keating. Last reply by Paul Craig Oct 17, 2019. 4 Replies

TDA2030A Amp

Started by Bama Hound. Last reply by Gary Stenzel Jul 23, 2017. 14 Replies

Home Brew Champ Tube Amp

Started by Scott aka Farmer Ted. Last reply by Paul Craig Feb 6, 2017. 3 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Jan 27, 2017. 29 Replies

5 Watt Amp Kit (DIY Case)

Started by Walter Haapapuro. Last reply by Gene Jones Dec 7, 2016. 46 Replies

DIY reverb behold - I found this online

Started by Danny B.. Last reply by Paul Craig Nov 2, 2016. 3 Replies

Bass Cabinet project

Started by Murdoc_420. Last reply by Murdoc_420 Jul 16, 2016. 34 Replies

Kalamazoo Model 1 Deluxe

Started by Scott aka Farmer Ted. Last reply by Rick Alexander Jun 20, 2016. 12 Replies

LM386 amp and other stuff

Started by Denis U. Last reply by Denis U May 29, 2016. 19 Replies

Latest Activity

Engblom posted discussions
2 hours ago
Uncle John commented on Randy S. Bretz's photo

Butternut coverplate / tailpiece in the works

"Yup!   It shines and looks like metal.  Great stuff."
5 hours ago
Uncle John commented on Poorness Studios's video

Cold Cold Heart (covered on dulcitar)

"I look for your Sunday posts every Sunday or Monday.   I like that inster munt. …"
5 hours ago
Uncle John commented on Cigar Box Nation's blog post Rest In Peace, Anonymous Pick. We Lost a Legend.
"Hey, Turtlehead and Slowpaw,  good to see you.  Pick got a lot of folks going here and he…"
5 hours ago
turtlehead commented on Cigar Box Nation's blog post Rest In Peace, Anonymous Pick. We Lost a Legend.
"Like a lot of people, pick was the first person who encouraged me when I signed up here. It meant a…"
8 hours ago
Pavel Danilov commented on Pavel Danilov's video
10 hours ago
Bernie Edwards commented on Randy S. Bretz's photo
10 hours ago
Bernie Edwards liked Randy S. Bretz's photo
10 hours ago
A.D.EKER replied to Engblom's discussion Making a Loud CBG
"Electricly ! i say Buy a BIG AMP ! acousticly ! i say use a Big Body ! the rest is up to You ! Good…"
10 hours ago
Taffy Evans commented on Randy S. Bretz's photo
18 hours ago
Taffy Evans liked Engblom's discussion Making a Loud CBG
18 hours ago
Randy S. Bretz posted a photo
19 hours ago


© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->