I decided I was going to build one of these after seeing a video on youtube(www.youtube.com/watch?v=0qFxXhg6zwA) of a electric one, but you can also build an acoustic one too.
What is a Tres Cubano you may ask?
It's a short scale(23" to 24") 6 string guitar that has the strings paired into 3 groups of 2. They use small gauge strings and pair the D string with high E, then 2 B strings and then a G string with high E and tune it gG-cC-dD(lower case is octave higher)like half of a 12 string guitar.
They are often used in Salsa music.
I got a couple short scale Strat type guitars for kids, but they were trashed. So I decided it would be better to build one out of a Cuban Cigar Box since my cousin gave me 4 Cohiba boxes.

Views: 195

Replies to This Discussion

Until I saw this I didn't know I'd built a Tres Cubano back in 2011 this was inspired by lute tuning, just thought it was a good idea at the time. Thank you !

That's really nice Mchael.

I've been paused on this build, I need a 12 degree radius block to use on my arbor press to get these frets completely seated and of course that block is nowhere to be found at the moment.
I have been working on 3 other guitars I have going at this time as well so there's that.

I finally got the neck finished and ready to attach to the box.
Now I get to shop for a tail piece or make one, then attach this neck.
I did the black and natural in a check pattern to match the black and white check pattern on the box.

Got the final clear coat on and put the nut on. I noticed that the neck now has a slight twist that's putting the high side up about a 1/16". I don't think it's going to be a problem as long as it doesn't go any further. Putting a tail piece on tonight and tuners. Then the electrical, jack, pots, preamp and corner pieces.

Got my aluminum shielding in place and once again there's no 60 cycle hum from the single coil pickups.

Got the Gitty piezo bridge and preamp installed, all is working well. Made a stop tail piece out of a Stratocaster tremolo spring claw that was in my parts bin and provided a string ground.

Next is cutting small string guide grooves in the brass bridge to keep the stings planted and tune it up.

I managed to finish this build and it turned out very nice.

I have the pickups and preamp wired to the same jack and turning the preamp on with the pickups, give the low output Lipsticks a boost. I like the lipstick pickups, but they definitely need a powerful amp or a preamp to boost their signal. Modern Lipstick pickups have more output for volume, but these vintage low output have better tone and need to be close to the strings for good volume.

Final pic....


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Discussion Forum

Frettin' and stainin'

Started by Douglas Allen Laffin. Last reply by Order99 on Thursday. 4 Replies

Bolt on neck to a set neck body?

Started by Paul Craig. Last reply by Paul Craig Jul 17. 14 Replies


Started by Roy Smith. Last reply by the anonymous pick May 15. 2 Replies

Help please re Bento Box Uke "nut"

Started by Al Lobe. Last reply by BrianQ. May 11. 18 Replies

Clarification on pick ups

Started by Michael Myers. Last reply by Taffy Evans May 6. 5 Replies

Licence plate cbg

Started by Michael Myers. Last reply by Michael Myers May 2. 5 Replies

Minimum tools needed

Started by Wichita Sam. Last reply by MadGomer Feb 27. 19 Replies

Doubling the high string

Started by Robert Killen. Last reply by Tim Pannabecker Feb 25. 22 Replies

Builder's Tips

Started by Wichita Sam. Last reply by MadGomer Feb 23. 2 Replies

Tres Cubano Build

Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies

CB Gitty Country Roads Banjo kit

Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies

Drawings or pictures on the box

Started by Martin. Last reply by Chad Taylor Oct 22, 2021. 6 Replies

Hard metal bridges

Started by Michael Myers. Last reply by Michael Fred Johnson Oct 22, 2021. 2 Replies

Getting the most sustain on a fretless CBG.

Started by Joe Plotts. Last reply by Taffy Evans Jun 30, 2021. 4 Replies

2nd Build Electronics Questions

Started by Steven Adler. Last reply by Steven Adler Apr 20, 2021. 4 Replies

yard sticks for fret boards

Started by Raymond L. Last reply by the anonymous pick Apr 17, 2021. 3 Replies

Where in the UK.

Started by Ian MCDONALD. Last reply by Lazylefteye Mar 28, 2021. 4 Replies


Started by andrew payton-smith. Last reply by Taffy Evans Mar 7, 2021. 11 Replies

Latest Activity


© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->