This has nothing to do with a CBG, but the situation I was dealing with and how I overcame it could be helpful to someone as far as building technique/solutions are concerned.

I acquired a set neck body for a SG type guitar on FB Marketplace for a good deal, finding a neck for it wasn't easy.
I had also acquired a Gibson scale bolt on neck for a cheap amount.
So I thought about adapting the bolt on neck to the set neck body. I was working on a set-neck SG kit and compared the 2 and decided that I'd make a "spacer" to glue in the neck pocket to bolt the neck onto or glue the neck to or both!

The spacer would have to have a degree cut of 4 degrees to give the neck the right tilt, but it would have to have the neck at the right height and the part in the neck pickup cavity would need to remain a certain thickness without interferring with the neck pickup height adjustment.

Using the kit set-neck to get all my adjustments and checking the bolt on neck measurements, then subtracting the last from the first, I was able to get the right measurements for the needed spacer. I made 4 spacers before I got it all correct and cut right. I used some Red Oak I had in my shop for strength and had to orientate the wood to ensure that I wouldn't be gluing or bolting into end grain.

The spacer at the body pickup cavity is 10mm thick, 12mm thick at the end of the neck past the 22nd fret and 5mm at the 17th fret where the spacer ends.
Total length of spacer is 115mm
Width is 57mm to fit the neck cavity tightly and happened to be right with the neck width.

I'll be attaching the spacer first and then the neck being careful to get it in it's right scale position, making sure it's high enough for strings to be in plane with the bridge and making sure the neck is straight so outer strings with have good spacing on the fretboard without dropping off.

Views: 525

Attachments:

Replies to This Discussion

these 3 pics show the mock up, the contour I'll need to carve and the way the spacer gives the needed degree.



Hey Rooster, you have to click the HTML Editor button on top right of the window to post.

I found out that the spacer is actually 1/16" too tall.

I made a jig for my router and got my router out and discovered that it got wet during storage and rusted up in lock mode. I got the motor freed up but the collet wouldn't budge after 4 days of sitting in penetrating oil. The router was 20 years old(Craftsman) so off I went to get a new one. My angle grinder died 2 months ago so I bought a new Dewalt angle grinder and router with plunge adapter for my Christmas present.

I got the spacer trimmed down, but noticed that the degree seemed off. Then it came to me, I made me degree jig 4 degrees from 90 degrees on my Miter Saw. That actually gave it a 8 degree angle on my spacer.
The spacer was already glued in so I cut a new spacer from 0 degrees and glued it in place. Now this body is ready to place the neck, get sanded for primer/paint/clear.
How did I get the 4 degree cut from 0 degrees on a Miter Saw that doesn't have a 0 mark? First I put a 2x4 in and did a 45 degree cut, with that board still in place I used it as a stop base and put my 1x3 board against it(standing up), move the degree setting back to 41 degrees and cut.

how did it turn out    ?

Hey Sam, I started painting, but the weather stopped me and then I went through a Sciatica attack that was real bad. It got up to 71 degrees yesterday and I thought I might get to work on paint and clear coat, but we 15 to 20 mile and hour wind, so no go. I may have to wait til spring.
The spacer for the neck worked out great once I figured out how to cut the degree correctly. ;)

So I have an update.

I had about 4 coats of Dupli-Color Artic White and 4 coats of 2X clear and it was hanging to dry inside of my bathroom to keep the bugs off of it. While it was hanging on a hook, the hook straightened out and it fell about 2 & 1/2 feet to the tile floor. It first hit the headstock and chipped the paint, then flopped on it top after managing to hit both sides putting 4 dents in the Mahogany. Good thing the neck is Maple or that headstock would probably have snapped off.

I've had nothing but a bad time with this guitar and the Gold SG I'm also building, it's like they are cursed or something. LOL

I did the clothes iron trick with the steam on a wet washcloth and got the wood to swell enough to remove 3 of the dents 100%. The 4th dent was on the upper horn and it was about 3/16s" deep, I got 90% of it out. The rest will get some wood putty after I sand it back down to the primer and start painting again. Urrrrrgh!

got all the paint off and down to the wood. fixed any dents or scratches and it's ready for primer. Just waiting on the weather.

Got it painted and oiled the fretboard. Added aluminum shielding and the tuners.
Next will be the bridge and stop tail piece and pressing in the bushings for them and cutting a few guard pieces. I'll be using Brown Tort material because it looks fantastic on White and too much Black would be bad.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Attention 1st time builders!

Started by BrianQ.. Last reply by T-Gripped 1 hour ago. 1 Reply

Brickhouse CBG Wiring

Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply

Cutting deep boxes in half

Started by Justin Stanchfield. Last reply by Taffy Evans Sep 20, 2023. 7 Replies

Fretless fret markers

Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies

canjo building and tuning

Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies

Minimum tools needed

Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies

High G problem

Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies

Doubling the high string

Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies

Aluminum License Plate

Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies

C. B. Gifty three string fretless kits.

Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies

Frettin' and stainin'

Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies

Bolt on neck to a set neck body?

Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies

Locations

Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies

Help please re Bento Box Uke "nut"

Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies

Clarification on pick ups

Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies

Licence plate cbg

Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies

Builder's Tips

Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies

Getting there but needing advice/help please.

Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies

Tres Cubano Build

Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies

CB Gitty Country Roads Banjo kit

Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies

Latest Activity

Carl Floyd liked BrianQ.'s discussion Attention 1st time builders!
1 hour ago
T-Gripped replied to BrianQ.'s discussion Attention 1st time builders! in the group Building a Cigar Box Guitar 101
"I would enjoy hearing more from Glenn. He was instrumental (pun fully intended) in getting me going"
1 hour ago
T-Gripped liked BrianQ.'s discussion Attention 1st time builders!
1 hour ago
BrianQ. added a discussion to the group Building a Cigar Box Guitar 101
Thumbnail

Attention 1st time builders!

If you’re wondering where to start, here’s square one:Article from cigarboxguitar.com …See More
1 hour ago
BrianQ. liked Glenn Kaiser's photo
2 hours ago
Andy joined Cigar Box Nation's group
Thumbnail

Building a Cigar Box Guitar 101

This group is for discussing the basics of CBG building for newer builders - where to start, what…See More
2 hours ago
BrianQ. replied to Joe's discussion Guitar for the grandson
"You could end up with an instrument that will never be in tune if you try to shrink the scale on a…"
2 hours ago
Doktor Bob updated their profile
2 hours ago
BrianQ. left a comment for Michael Starnes
2 hours ago
BrianQ. left a comment for Gloria Wilson
2 hours ago
BrianQ. left a comment for Doktor Bob
2 hours ago
BrianQ. left a comment for JP
2 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->