so far ive done angled necks , scarf heads , bolt ons ,neck through, but i have not done a tapered neck and figure it is my next step . I dont want it too skinny on the head end and not crazy fat on the body end . just a nice slight taper . my thought was use an average guitar neck and half it but that leaves neck looking and feeling like an arrow . who has done a tapered neck and doesnt mind whispering a few secrets ? O.o
Tags:
I'll offer my two cents...I take the body and rough neck blank, before shaping, and lay them together as if built/finished. I decide scale length, mark a line on the neck where nut will be, and place a piece of masking tape across the box or solid body where bridge will be. Then I make marks at the nut location indicating the string spacing ...then I use a long straight edge and draw a line for the two outside strings (same process for 3, 4, 5, 6 string) to their respective locations on the bridge. Note: I typically space strings at the nut at 3/8", more or less, and a slight bit wider at the bridge.
Once the two outside string lines are marked, I measure 3/16 inch outside of those two marks at the nut, and the bridge. This second line is your cut mark. 3/16" may seem like too much, but after cutting, sanding, finishing, the edge of the neck will be at a comfortable width and not be too narrow at top, or fat at bottom....instead, more symmetrical and balanced.
WARNING: If you'd prefer to learn this by making your own mistakes, don't read on. Additionally, if you'd like not to make my mistakes, please don't follow my directions. Additionally, if you don't want to agree with the way I do it, then don't read on. Hahaha.
Ron is right. I double taper my necks. The width across the fretboard doesn't taper all that much, usually. The thickness will taper and it depends on what I'm building - mainly down to the number and intended gauge of strings.
Here's my rough process:
BTW, there is a lot of sanding in there. Plenty of rasping, but not much swearing unless I make a mistake.
Here's the video describing my last complete resonator build and it shows the taper I put in the neck. If you want to step up your game, build a reso with a fixed saddle position. That will make you sweat the details! I have changed my building procedures after learning from this one. I'll pass on my biggest lesson for resos. Don't fret it until almost last when everything is in place and you can measure your final scale length as it acutally is, rather than try to build to a specific scale length. I'm talking mm accuracy here. If you fret it nearly last when the bridge and nut are fixed, then you can make the minor adjustments. If you fret it based on the nut location and where you think the bridge will be, then you had better well be right.
An excellent and informative reply. I learned a lot from it!!
Thanks Dan. I've left plenty of room for mistakes. . .I mean learning opportunities. . .in that summary. I've built more than a dozen but less than 20 guitars now, I think. I think there are always ways to challenge yourself and not become bored. I've tried all sorts of different techniques on each build and I'm just starting to get into more complicated carvings and rudimentary inlays. The possibilities are almost endless. Well, they are endless if you don't have a plan to sell the guitar for a set amount of money which would either limit materials, your time investment, or both. I'd never make any money at this hobby.
Thanks guys ! exactly what i was looking for . i wanted a challenge and this seems like it . just needed a little push in the right direction . still dont have power tools so this should be fun haha . that double taper is beautiful . again thank you . so much you guys have learned and instead of keeping it all to yourselves you dont even hesitate to pass it on .
I got no trade secrets! I totally respect the guys who do and I'm not trying to take money out of anyone's pocket, but I'm happy to share what I've learned.
My next attempts will be adding a binding to the edge of the fret board so you can't see the fret slots. I used to think it was silly to frig around with all these details on a CBG, but now I realize why some of the builders do it. Always have to keep things interesting. :)
i use mostly scrap and cheap stuff . the next one will have a type of binding . i was in walmart and found this stuff called "craft lace" its a flat square small plastic string . im trying it on this one now . i just got tired of straight necks . it gets boring doing the same thing over and over . i can slap a guit together in a few hours . after i get my necks down how i want them im going to look into making boxes out of tone woods . that way they will be full blown guitars but with the soul of a cbg . ;)
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. 4 hours ago. 4 Replies 0 Likes
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by A.D.EKER yesterday. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango on Tuesday. 4 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods on Saturday. 7 Replies 1 Like
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Carl Floyd Mar 1. 15 Replies 0 Likes
Started by Joe in Performances, How to Play, Lessons, Concerts. Last reply by Carl Floyd Feb 29. 13 Replies 0 Likes
Started by Chance in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Feb 22. 12 Replies 1 Like
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
May 11, 2024 from 11am to 8pm – Speakeasy Grill
0 Comments 0 LikesMay 30, 2024 from 6:30pm to 10pm – The Casual Pint of Huntsville
0 Comments 0 Likes© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!