Hi, I'm having a problem tuning the high G string on the CGB I have just built. Initially no problem, strung it up, played it, everything OK. The high string snapped when I tried to up the tuning to G#, so I replaced it with a 28 gauge bronze wound and it snapped again just before high G. I have tried a 29 gauge bronze wound and a .009 nickel wound and they also snapped at F#. so I can't get it tuned up. The scale length is 25 inches held at the tailpiece by a hinged bracket. as illustrated in the photo.  All strings snap at the tailpiece. Could this be causing the problem?  I have another 25 in scale CGB with strings threaded through holes in the tail section and don't have the same  problem. 

Views: 647

Reply to This

Replies to This Discussion

It wouldn't hunt to smooth any sharp edges on the holes in the hinge but those are some mighty thick strings Alex. What octave are you trying to tune to?

Tuning a .029 bronze to G2 would only be about 10lb of tension, so too loose, tuning it to G3 would be about 40lbs which is way too much in my opinion. If you were going for G4 the string would snap before you got it up to the 170lbs needed.

Thanks for your advice guys.  Low G and middle D are tuned to G1, I've tried tuning down to the octave below but this makes the strings too loose. So I have been trying to tune the high G to the next octave up, which would be G2. When tuning up the string becomes incredibly tight, more so than my other CBG which I have tuned up to G# with no problem. Not sure of the gauge of the strings on that one as I didn't build it but they are lighter bronze wound but still quite thick.

I have been considering removing the hinge and threading the strings through drilled holes the tailpiece to see if that helps. Lighter strings might improve things.

That's a better plan. I would leave the hinge on and drill through the tailpiece so the strings still go through the hinge, but at a much shallower angle. That will keep the look you already have with minimal modification. You will probably need metal eyelets or ferrules on the back of the tailpiece to prevent the ball ends from chewing into the wood. The hinge will protect the wood on top.

That's a tough bend for a string to make through the hole in the hinge. It's essentially a 180 degree bend. You could put something (small dowel, nail, machine screw...) behind the hinge to round out the bend and ease the stress on that point. A piece of wire insulation might work. Strip the insulation and run the string through it so the insulation cushions the string around the bend. Stevie Ray's guitar tech used that trick when he was breaking strings at the saddle.

The string gauges I use are similar to the third (G), fourth (D), and fifth (A - tuned to G) strings on a six string. So my string gauges are 0.018", 0.026", and 0.038". The high G is not wound, so you can get a more singing slide tone. The other two are wound. No tuning issues.

Instead of looping the string through the bead, thread it through a small washer and then through the hinge.  Here's one using copper rivet washers on a similar hinge, been using it like this for a year with no breakage.

Yep, works for me too.


Thanks for the advice Don, this would reduce the strain in the strings, I think it would be a good idea to use lighter strings.

The Cigar Box and some of the hardware in the build came from someone local who makes CBGs and in his experience if the tuning peg isn't sitting right it can cause problems. On checking I found  the peg for the high G string is wobbling slightly. He is at a local Americana music event this weekend and offered to look at it for me. I'll keep everyone posted on developments.

I use a .026 wound for my high G string... even then, they're pretty tight...  Probably a combination of all the great suggestions above...

Pretty sure those holes on the hinge are countersunk , which makes them like the edge of your wire cutters. Maybe file them out and use the brass washer trick shown in here instead of looping them back at that sharp angle.

.029 is WAY too heavy for a high G - that's about right for D, but you need to be around .020-.024 for a high G


The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Handy adhesive

Started by John B Treutlein in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 17. 11 Replies

String noise

Started by Michael Myers in Performances, How to Play, Lessons, Concerts. Last reply by Michael Myers Mar 17. 6 Replies

Build this Wooden Kick Drum Pedal

Started by Rose Ericson in Feature Articles. Last reply by Slow Mick Mar 16. 35 Replies

Neck though corner

Started by Engblom in Building Secrets, Tips, Advice, Discussion. Last reply by Michael Fred Johnson Feb 28. 6 Replies

Latest Activity

Scott Schoepf liked BrianQ.'s photo
7 minutes ago
Derek Robertson commented on Derek Robertson's photo


"Iive been sitting on this box for a few years just got round to it.thanks for your interest."
5 hours ago
AGP # commented on AGP #'s photo

AGP #493 - ''Juzzie''

"Juzzie Smith Bamboo Lap Slide"
8 hours ago
AGP # posted photos
8 hours ago
Doug Thorsvik commented on Richard Sundberg's video

Going Down To CALLYFEST. A. D. Eker

"The ball is rolling now!!! See y’all at Califest."
10 hours ago
Doug Thorsvik commented on James O Lunsford's video

Going to Cally Fest

"Very creative James O! See you there."
10 hours ago
James O Lunsford liked Calvin Fowler's photo
10 hours ago
James O Lunsford liked Derek Robertson's photo
10 hours ago
James O Lunsford commented on James O Lunsford's video

Johnny Be Good On Dulcimer

"Thanks Rick Rex has a new Airship! He's riding Us to Cally Fest in It's super cool. room…"
10 hours ago
James O Lunsford commented on Richard Sundberg's video

Going Down To CALLYFEST. A. D. Eker

"Oh yeah! remember the good times see everyone There! Pick and Dave would want Us to have a great…"
10 hours ago
James O Lunsford liked Richard Sundberg's video
10 hours ago
James O Lunsford commented on James O Lunsford's video

Going to Cally Fest

"Thanks Rick tell them not to worry Rex a put fire out! as fast as He can start um We can set up the…"
10 hours ago


© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->