Apologies if this has been covered elsewhere but what is the best (easiest) technique for measuring from the first fret to the nut?

Previous efforts have always resulted in bad intonation.

Also if I file the slots how do I ensure the string is leaving the nut at the front edge and not half way through or even at the tuning peg side?

I realize this is CBG101 stuff but that's the level I'm at!

As always, thanks for the advice which I am sure will be invaluable, prompt and free! Things don't get any better than that!

 

Views: 528

Reply to This

Replies to This Discussion

Assuming you are using a bone nut blank, the easiest (best) way is to establish your nut position BEFORE any fret positions. In other words, do not cut your first fret slot and follow by attempting to set your nut position. Because it is the nut position that is your zero mark for setting all of your fret slots/locations.

As for ensuring that the nut slots for the strings are proper, simply be careful to cut/file those slots so they slant downward toward the headstock...not flat.

Not much to add to Scott's response, but I'd suggest working in millimeters instead of inches. I'm not sure where 1.814 inches is on the ruler, but 46.076mm is pretty easy to find (46 is close enough). Measure each fret from the nut. Not fret to fret. If you make a mistake on fret it will be compounded on each one after that. 

When I first started with frets I used the same scale length as a manufacturd guitar I owned. Once I had them all marked out (I got the fret positions using the calculator on Stewmac's website) I could place the necks beside each other and make sure I wasn't way off on my measurements.

That's very useful stuff guys - I'll take that on board. Now to the shed.....

I also use a fret calculator, like most, for fret layout.  Much easier.  I have several templates I use in the scales I build in.  The hardest part of the process is calibrating your printer which took me all of about 5 minutes.  Once you have a template then laying out where your bridge will be located, as well as frets,  is about as simple as it gets.  Even I can do it...  )

Set nut (I use zero fret, super simple).
Measure nut to desired bridge position (who cares what scale length it is).
Multiply measurement by 0.9439 = fret 1 ... Multiply this number by 0.9439 = fret 2 (repeat until you run out of fret board)
Check 12th fret is in the middle.
Easy peasy.

It's possible that your nut position is fine, but your action is too high. If the strings sit too high in the nut it will make at least the first few frets play sharp. Scott's tip on filing the slots slanting down towards the headstock is really important too.

That's why I build zero fret guitars. Get the action/string height correct and there's no need for a nut. You just need lateral/horizontal (how is it described, note bend?) fixing.

google search to the rescue again

Thanks for all the replies guys.

Zero fret I think next time - can't be much different to placing a capo on a normal guitar surely?

I like the diagrams and they help greatly.

Cheers!

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Uncle Toad yesterday. 5 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray on Thursday. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

HELP !! IN VERMONT.

Started by Ranblin' Dan Stevens in Other stuff - off topic, fun stuff, whatever. Last reply by Patrick Kelly Jan 21. 7 Replies

Fat Back Neck

Started by Jim Booth in Building Secrets, Tips, Advice, Discussion. Last reply by Jim Booth Dec 15, 2023. 7 Replies

Brick House CBG

Started by Ian Boyd in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Dec 13, 2023. 3 Replies

Latest Activity

AGP # liked Glenn Kaiser's photo
26 seconds ago
AGP # liked A.D.EKER's video
55 seconds ago
A.D.EKER commented on A.D.EKER's video
31 minutes ago
A.D.EKER posted a video

Rapture (instrumental) BCB 2024

a Instrumental to catch the vibe for a Sunday Gathering Playing on the Porch just a warm up getting the Juices flowing and a good portion of blood to the f...
36 minutes ago
Taffy Evans replied to Joe's discussion Guitar for the grandson
"Hi, or you could start your scale length at the 5th fret of your 25.5 scale. As if using a capo,…"
40 minutes ago
Carl Floyd liked BrianQ.'s discussion Attention 1st time builders!
2 hours ago
T-Gripped replied to BrianQ.'s discussion Attention 1st time builders! in the group Building a Cigar Box Guitar 101
"I would enjoy hearing more from Glenn. He was instrumental (pun fully intended) in getting me going"
2 hours ago
T-Gripped liked BrianQ.'s discussion Attention 1st time builders!
2 hours ago
BrianQ. added a discussion to the group Building a Cigar Box Guitar 101
Thumbnail

Attention 1st time builders!

If you’re wondering where to start, here’s square one:Article from cigarboxguitar.com …See More
2 hours ago
BrianQ. liked Glenn Kaiser's photo
2 hours ago
Andy joined Cigar Box Nation's group
Thumbnail

Building a Cigar Box Guitar 101

This group is for discussing the basics of CBG building for newer builders - where to start, what…See More
2 hours ago
BrianQ. replied to Joe's discussion Guitar for the grandson
"You could end up with an instrument that will never be in tune if you try to shrink the scale on a…"
2 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->