I’m trying to make a guitar that I can play by removing the frets epic Ying the fretboard and then just sliding up and down the strings, I’ve got some experience making Diddley bows but I’m unsure of exactly what I need to do in order to get somthing that has a metal sound, if anyone has tried this I would like advice to avoid breaking my budget messing things up

Views: 289

Reply to This

Replies to This Discussion

I`m trying to decipher your question but I gather you want to take the frets of a guitar to make it into a fretless guitar? Well, if you do have an old guitar you don`t care for then stripping the frets off it will do exactly what you want. You just need to raise the strings a little of the board as a fretless is usually slightly higher action.

You can either leave the grooves left from the frets or you can use a good filler to give your fretboard a nice smooth finish. Also if you do that with a different colour filler you will have fret guides to make playing easier! 

Higher action if you are playing with a slide... but extremely low action if you are playing fingered fretless.  ;-)

When you say “metal sound” does that mean distortion or the sound of a metal cone resonator? 

Hi, yes these questions baffled me too, so could not respond, 

Taff.

So basically, I wanna take a guitar, or bass depending on what we think an appropriate scale length would be for the correct ish sound, but bassically just go listen to back to the primitive by soul fly and try and pick out the rhythm section with your ears.

Then come back and read the following.

It’s my belief that I can recreate a heavier version of this tone, with a fretless guitar with a glass like fretboard.

The origional is played on a four string guitar apparently just powerchording in ascension, but by being able to “waver the notes up and down I believe I can crate a continuous drone sound that can then be used as a backing for a kind of re imagined tribal drone style of metal I’m trying to create.

I have seen them live quite a few times , so I’ll tell you what I think. Firstly, they all play in drop tuning(drop B) B,f#,b,e,g#c#, which gives them that ominous sound? 3 big strings are tuned same as open tuning, so drone sliding around is a breeze, especially with a slide. As for the metal part, that depends on your aptitude for playing the said style & a truck load of volume & distortion? Once you have those in place, you’ll more or less get what you’re looking for? Here’s a little video lesson on metal droning from a friend of mine, hope this helps :) 

https://m.youtube.com/watch?v=kPu-7GBp_1s&list=PLEpiTBdaAD-UDbX...

There are several way's to go about that, build a four string lap slide ,whit your bridge base a tin or something metal preverably a cigartin ,a monster pickup , string tuners,  tone control , volume,  truckload of FUZZ Distortion, sustain pedals, maybee  reverb and echo, that helps getting loads of sound and doing only a little(Playing wize) and like BrianQ proposed  dropped tuning, i recomend Drop D  grunts real nice and Low. Use some easy to work on wood , use not to thin strings NO 008 - 009 use minimum 10 or 12 for your thinnest 4 string and go up to your wound string accourding the used set, and i recomend a lapsteel metal slide no glass slide!! metal or ceramic ,will give you the best sustain ! good luck on your build Let us know what you came up whit and if it all worked out for you !! Greeeeeettsszz A.D. From Holland!

I’m just gonna do it without any help cos I can only explain it so many ways and if you don’t get it then you just don’t, I can’t be more clear because what I’m trying to do doesn't exist yet

Ok then, I’ll give you some parting advice for your future neck deconstruction

Only use Pliers like these to pull frets-they will allow a clean job & won’t cause irreparable damage? You can find the smaller ones in the pic at hardware stores for a cheaper price if pro luthier style one’s aren’t in the budget?

And, before  Applying Epoxy over a fretboard, clean it thoroughly with alcohol & use quality masking tape to protect the sides-or you’ll get bleed over, especially if the neck is not clean? 2-part Epoxy resin gets pretty hard & glassy depending on the ratio of the hardening catalyst, just a thought? 

Hi, I think going it alone on a project that's a sort of experiment that only you know what the final outcome should be is the way to go. A number of your descriptions or terminology used were a bit misleading.

1 - Metal Sound - Use a tin box of a suitable size for a body. If its metal music refer to Brian and A D Ekers suggestions
2 - Scale length - would have a minimal effect on the sound. Of course, body size would. EG: guitar or bass.
3 - When you say the Rythme section, do you mean the bass line only, or the other backing instruments also?
4 - Creating a heavier tone - I assume that means deeper bass tones? Again, body size would help more with achieving that.

Having said all that and rereading your post, I think you are referring to a band when you say primitive and soul fly. If I get time I'll have a look if that is the case.

Anyway you have some info to work with now, post back when you get it all sorted, sounds interesting
Cheers Taff

Hi Ozz989, I was right your comments did refer to a band and as promised I had a listen to it. 30 seconds was enough for me haha, but forced it to a minute.

On the track I listened to the rhythm section you mentioned to my ears was mainly drums, and the bass lines did not cut through very well. So can not help you any further on that one.
Just a thought though to answer another of your questions, if you are slide playing it should not matter what the fingerboard is made of I'm thinking.
Good luck Taff

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans yesterday. 8 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

BrianQ. liked Gary O'slide's video
57 minutes ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

"Thanks. Wow! That becomes a spendy box Alan. They are pretty distinctive though. I have a few on…"
5 hours ago
Nigel McTrustry posted a video

Nigel McTrustry & The Hound Dogs are Loose! - Yellow Dog - Live - Original - Cigar Box Guitar

Nigel McTrustry & The Hound Dogs are Loose! Yellow Dog (McTrustry)@ The Cave Inn Brisbane, Australia.The song is currently on Spotify.
5 hours ago
AGP # commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

""Sweet Doug" :-), have seen quite a few Flathead Builds over the years, great looking…"
7 hours ago
AGP # liked David Dodt's photo
7 hours ago
AGP # liked David Dodt's photo
7 hours ago
AGP # liked David Dodt's photo
7 hours ago
AGP # liked Doug Thorsvik's photo
7 hours ago
AGP # liked Doug Thorsvik's photo
7 hours ago
AGP # liked Doug Thorsvik's photo
7 hours ago
AGP # liked Aaron Green's photo
7 hours ago
Keith Rearick liked Gary O'slide's video
8 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->