I just finished a couple of Cigar Box amps. Everything went well until I soldered the LED leads. I bought 2 prewired kits from Gitty. I checked the the leads with an ohm meter and had good continuity from the circuit board to the ends of the lead. Neither one of the LED's lit up when I turned on the switch. The amps both work well although not to loud. I can't figure out why the LED's don't lite. Take a look at the picks. Any help would be great

Views: 846

Reply to This

Replies to This Discussion

 I may be wrong but I seem to remember when building shifts lights for my track car the LED has one leg longer than the other  so maybe if you change the wiring round , does it tell you which way round the wire the LED ?

both leads to the LED was the same but I did change them around and when I put together the 1st amp and the LED didn't work I used the one from the other kit and it didn't work either. Whats the chances that I got 2 bad LED lights. I checked the connections to the amp circuit board and the leads are in the right place according to the diagram supplied with the kit. I used one of these kits about a year ago without any trouble.

Strange that they sent the LED with equal legs , as how do you know which way to hook them up ? they should as I said have one leg longer which is the live and the shorter one the neg .

I think there should be a notch on the base of the LED and that will be a reference point. But that aside - if they don't work the way you have it - the other choice is - try the other way.
I feel your pain - those LED's drove me crazy, as well.
Do you need to pair a resistor with it to work properly??

I went out and bought some new LED's from radio shack, they were clearly marked. I just finished hooking them up and they are working just fine. I must have had two faulty LED's from the kit. What are the chances of that, and I did try the other way.

I may be wrong but iirc If you hook up an LED the wrong way round the voltage kills it. They may have been fine at first but you may have unluckily wired both of them up the wrong way and blown them...

You may be right, I did power them up before I switched the leads. I have been known to make a few mistakes when building CBG's or Amps. I'm retired so I have plenty of time to fix them thanks to the folks on CBG nation.

diodes only conduct one way. chances are you fried them if you hooked them up backwards. the notch should be the positive (+) side.

I didn't see a notch and it probably wouldn't have meant anything to me any way. Live and learn but thanks for the response. I'm all squared away now and the new LED's are working fine, and so are my CBG amps

Looking damn good too! Love those speaker covers!

Usually you need a resistor before the LED to drop the voltage, you may have over powered it and smoked it. You'll want to look at the specs for your LED but the ones I use get a 330Ohm resistor.

You can also tell the +ve lead by the short tang inside the globe.

Sorry the resistor is to limit current not voltage(knew I had that wrong as soon as I posted it). Size your resistor here

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Forum

Box thickness effect on sound

Started by Infirmity Citrus President in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans on Tuesday. 2 Replies

The Cigar Box SITAR Experiment - by Shane Speal

Started by Cigar Box Nation in Feature Articles. Last reply by t-belly johnson Jun 16. 2 Replies

Build a Les Claypool Whamola!

Started by Ben "C. B. Gitty" Baker in Feature Articles. Last reply by Cindy J Jun 14. 11 Replies

How to Build a Mailbox Dobro

Started by Cigar Box Nation in Feature Articles. Last reply by Cindy J Jun 13. 3 Replies

Latest Activity

Uncle John commented on Uncle John's photo
Thumbnail

Spent $20 on vintage boxes, license plates and match books.

"Doug, I can't read the plate year, but I think it is not so very old.  But sure beat up!"
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
3 hours ago
Doug Thorsvik commented on Uncle John's photo
Thumbnail

Spent $20 on vintage boxes, license plates and match books.

"Concur on the Texas plate Uncle John. I have one of those in my stash, just not as old."
3 hours ago
Uncle John commented on Doug Thorsvik's video
3 hours ago
Uncle John commented on A.D.EKER's video
Thumbnail

Don't want to work for the Big Boss no more A. D. Eker 2022

"Raunchy good tone going.  Appropriately pissed off.   I don't want to work for…"
3 hours ago
Uncle John commented on Uncle John's photo
Thumbnail

Spent $20 on vintage boxes, license plates and match books.

"Thanks, Doug and Alan.  I feel like I got lucky.   The Texas plate is my fave…"
3 hours ago
Uncle John commented on Uncle John's photo
Thumbnail

Spent $20 on vintage boxes, license plates and match books.

"Wow, Brian.  I would not have any at that price.  It is purty.  I may yellow over…"
3 hours ago
Doug Thorsvik posted a video

He Keeps Me Singing: 3-String Surf SLG Cigar Box Guitar

Cigar Box Guitar Slingers - Spokane, 110th Zoom Mtg June 20, 2022. More info and free songbooks: https://sites.google.com/site/cigarboxguitarslingersspokane/...
3 hours ago
MadGomer replied to Taffy Evans's discussion While we are talking solid body resonator guitars.....
"Beautiful!"
12 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Don't want to work for the Big Boss no more A. D. Eker 2022

"I don’t either A.D., so I’m not anymore! Retirement is great. Excellent musical…"
14 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #245 - ''Dud Sanshin''

"Thanks for the details AGP! I do enjoy the rationale behind some of the design decisions.…"
15 hours ago
A.D.EKER commented on A.D.EKER's photo
Thumbnail

Minimal LoFi 4 String

"Yup You got it kale ! "
15 hours ago

Music

© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->