I just finished a couple of Cigar Box amps. Everything went well until I soldered the LED leads. I bought 2 prewired kits from Gitty. I checked the the leads with an ohm meter and had good continuity from the circuit board to the ends of the lead. Neither one of the LED's lit up when I turned on the switch. The amps both work well although not to loud. I can't figure out why the LED's don't lite. Take a look at the picks. Any help would be great

Views: 846

Reply to This

Replies to This Discussion

 I may be wrong but I seem to remember when building shifts lights for my track car the LED has one leg longer than the other  so maybe if you change the wiring round , does it tell you which way round the wire the LED ?

both leads to the LED was the same but I did change them around and when I put together the 1st amp and the LED didn't work I used the one from the other kit and it didn't work either. Whats the chances that I got 2 bad LED lights. I checked the connections to the amp circuit board and the leads are in the right place according to the diagram supplied with the kit. I used one of these kits about a year ago without any trouble.

Strange that they sent the LED with equal legs , as how do you know which way to hook them up ? they should as I said have one leg longer which is the live and the shorter one the neg .

I think there should be a notch on the base of the LED and that will be a reference point. But that aside - if they don't work the way you have it - the other choice is - try the other way.
I feel your pain - those LED's drove me crazy, as well.
Do you need to pair a resistor with it to work properly??

I went out and bought some new LED's from radio shack, they were clearly marked. I just finished hooking them up and they are working just fine. I must have had two faulty LED's from the kit. What are the chances of that, and I did try the other way.

I may be wrong but iirc If you hook up an LED the wrong way round the voltage kills it. They may have been fine at first but you may have unluckily wired both of them up the wrong way and blown them...

You may be right, I did power them up before I switched the leads. I have been known to make a few mistakes when building CBG's or Amps. I'm retired so I have plenty of time to fix them thanks to the folks on CBG nation.

diodes only conduct one way. chances are you fried them if you hooked them up backwards. the notch should be the positive (+) side.

I didn't see a notch and it probably wouldn't have meant anything to me any way. Live and learn but thanks for the response. I'm all squared away now and the new LED's are working fine, and so are my CBG amps

Looking damn good too! Love those speaker covers!

Usually you need a resistor before the LED to drop the voltage, you may have over powered it and smoked it. You'll want to look at the specs for your LED but the ones I use get a 330Ohm resistor.

You can also tell the +ve lead by the short tang inside the globe.

Sorry the resistor is to limit current not voltage(knew I had that wrong as soon as I posted it). Size your resistor here

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Forum

Box thickness effect on sound

Started by Infirmity Citrus President in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Jul 31. 3 Replies

Ghost pickup

Started by Michael shrader in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans Jul 29. 5 Replies

Files download

Started by David Herrera in Performances, How to Play, Lessons, Concerts. Last reply by Timothy Hunter Jul 14. 9 Replies

Latest Activity

Michel liked Rob Uker's photo
37 minutes ago
Rob Uker commented on Jim Winslow's photo
Thumbnail

509D8F2B-B281-484A-88A7-468F8B08AFF2

"Nice Danelectro inspired Longhorn."
2 hours ago
Rob Uker liked Jim Winslow's photo
2 hours ago
Darryl Tuttle commented on Randy S. Bretz's photo
Thumbnail

Cherry bench done

"Looks like the perfect bench to sit and play guitar"
4 hours ago
Infirmity Citrus President posted a discussion

The entirely hypothetical encylopedic CGB design and construction book - a long post

I just bought a box full of CGB building books, and I must say I'm disappointed. I taught…See More
7 hours ago
BrianQ. commented on Randy S. Bretz's photo
Thumbnail

Cherry bench done

"I would too!!!"
7 hours ago
Randy S. Bretz posted a photo

Cherry bench done

My wife said she loves it !
8 hours ago
Uncle John commented on Matthew Borczon's video
Thumbnail

Dinks song

"Thanks a lot, Matt. '"
9 hours ago
Maddog commented on the anonymous pick's blog post UPDATE on my health issues
"I have not been on CBN for some time but did see your message a few days ago and needless to say…"
9 hours ago
Keith Rearick liked Poorness Studios's video
10 hours ago
Keith Rearick liked Matthew Borczon's video
10 hours ago
Keith Rearick liked Pavel Danilov's video
10 hours ago

Music

© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->