Well, it was actually not that close to an explosion, but it could have been.

I think I knew this already, but had forgotten how much static electricity a belt sander can generate, especially during the winter dry season. The sanding belts can create quite a bit of static, especially when the grit on the sandpaper has worn down.

I have one similar to this one, but with the 5 inch disc sander on the side.

http://www.harborfreight.com/1-inch-x-30-inch-belt-sander-2485.html...

I had just been wiping something down with a rag and some lacquer thinner, and I tossed the rag on the workbench that my sander was sitting on. I went to smooth up a piece of red oak, and when I touched the metal casing to turn it off, there evidently was just enough spark from my finger to ignite the small amount of fumes caused by the solvent rag. It went "whoosh" and I saw a flash of flames. It went out immediately, but had there been a container of solvent nearby, the outcome could have been much worse.

So the moral is, you gotta be careful using flammable stuff in your shop. An ignition source can come from the most unlikely places!

Views: 736

Reply to This

Replies to This Discussion

Wow, A change your drawers kind of thing!Glad thats all it was.

Dan. You always where a bright spark, but that is taking it a bit too far.

One solution is to live on a relatively small island surrounded by sea (which is, after all, pretty much the definition of an island). We don't have dry seasons. Only wet ones and really wet ones. The only consolation is that it is (much) worse in Wales.

So I am guessing that static is not so much an issue in your neck of the woods...



Roadkill a.k.a. John Maw said:

Dan. You always where a bright spark, but that is taking it a bit too far.

One solution is to live on a relatively small island surrounded by sea (which is, after all, pretty much the definition of an island). We don't have dry seasons. Only wet ones and really wet ones. The only consolation is that it is (much) worse in Wales.

By contrast, it's so dry where I live, that there's not usually enough moisture in the air to transmit a spark.

Some people give that as the reason why this place occasionally seems like it's still in the Dark Ages.

>-:E

OK, I meant that as a bad joke; in reality, I'm about 6 km from the coast, and for at least 5 months of the year, it can be really humid. And hot. I actually have shocked myself once in similar fashion, and the culprit was also a belt sander. Fortunately, there were no solvent soaked rags around. Just glad you're OK, Dan.

dan "sparky"? sleep

Tell me about it, I live in N Wales, never stops blowing gales or raining.

Hogs.

Roadkill a.k.a. John Maw said:

Dan. You always where a bright spark, but that is taking it a bit too far.

One solution is to live on a relatively small island surrounded by sea (which is, after all, pretty much the definition of an island). We don't have dry seasons. Only wet ones and really wet ones. The only consolation is that it is (much) worse in Wales.

Safety with solvents - especially lacquer:

If spraying indoors you should have a spray booth with explosion proof lights and explosion proof fan, a filter wall and it exhausts to the outside. You should always use a charcoal spray mask and gloves when handling lacquer/lacquer thinnner.

Anything you breathe or touch gets absorbed into your body. It's bad stuff - can cause cancer, chemical sensitivities if you have the wrong genetics like me, and so on.

Which is exactly why I spray my stuff outside, and never in the garage. I think this points out how little fumes are needed to generate a quick little flash. I had used a very small amount of thinner on the rag, but that was all it took.

Skeesix said:

Safety with solvents - especially lacquer:

If spraying indoors you should have a spray booth with explosion proof lights and explosion proof fan, a filter wall and it exhausts to the outside. You should always use a charcoal spray mask and gloves when handling lacquer/lacquer thinnner.

Anything you breathe or touch gets absorbed into your body. It's bad stuff - can cause cancer, chemical sensitivities if you have the wrong genetics like me, and so on.

In junior high shop class it was a great trick to load yourself up with excess electrons on the sanders or buffer then find a victim who wasn't paying attention. You could let loose those electrons on the back of their neck. Reportedly.

Anyway, glad yours was just a little excitement and not a disaster.

Two separate problems combined into one big potential disaster there Dan.

In addition to the solvent cautions above, (below?) always beware of solvent soaked rags. They can spontaniously ignite even without the static spark discharge! And the static produced by the sander is a warning, beware also of dust collection systems, and static build up, and always remember that in the right conditions, airborn wood dust can also be a serious combustion hazard!

It never ceases to amaze me how the seemingly unlikely can so frequently occur!

Now, want to know about gasoline spray while changing a fuel filter does when it hits a hot incandescent drop light? How about what happens while using acetylene torch to heat something too near a 30 gallon waste oil drain full of Brake-clean fumes?........ Ever drain all the oil out of a race car and attempt to braze some small holes scraped into the bottom of the oil pan and blow the valve covers clean off from the fumes igniting?  Wait, I have more...... NOT good days.

Consider yourself lucky, and warned by the cosmos.

Lets not forget about the fumes ! They can be pretty nasty. After reading the posts here, makes me feel even better for ordering my new North dual filter face mask to be used when spraying and sanding  :)

 

Be SAFE guys.

We need your continued pics posted to help inspire!!!

My two cents, always store your flammable solvents in a flammable storage cabinet. It may save your garage or your life.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

Best power tool for building?

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield 17 hours ago. 2 Replies

Fat Back Neck

Started by Jim Booth in Building Secrets, Tips, Advice, Discussion. Last reply by Carl Floyd on Thursday. 2 Replies

Back of the box or the lid?

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Dec 2. 8 Replies

Pin Tin Banjo

Started by Michael Bowlin in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Nov 1. 11 Replies

EBE tuning

Started by Thomas A Morphew in Performances, How to Play, Lessons, Concerts. Last reply by Carl Floyd Oct 30. 2 Replies

Blog Posts

Who will be the first to embed GO in CBG? =)

Posted by Vlad on December 6, 2023 at 12:17am 4 Comments

My first CBG from Captain Nemoff.

Posted by Vlad on November 29, 2023 at 3:41am 0 Comments

New Album 2023

Posted by Gary O'slide on November 5, 2023 at 2:41am 0 Comments

Latest Activity

3 String Blues posted a photo

we all want to be like somebody!

-------------I'm still trying to find the right tuners for the price ratio : )----------------
52 minutes ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

White Christmas: 2-String Surf Chugger Cigar Box Guitar

"white christmesis ahhh those old day's getting special by the year ,we did have some , but im…"
3 hours ago
A.D.EKER commented on Poorness Studios's video
Thumbnail

The Letter (Box Tops cover on tenor ukulele)

"Box Tops ! yep thats a fine one , use to love that grunge ,raspy voice, a lovers tune ! instant…"
3 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Turkey in the Straw BCB - A. K. A.- A. D. Eker 2023 - 2024

"Thank you Doug ! for liking my fancy picking ! i did try to keep it period real!"
3 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Turkey in the Straw BCB - A. K. A.- A. D. Eker 2023 - 2024

"Interesting take on a classic tune! Fancy pickin’ Andries."
4 hours ago
BrianQ. updated their profile
5 hours ago
BrianQ. liked Poorness Studios's video
5 hours ago
A.D.EKER commented on A.D.EKER's video
6 hours ago
Carl Floyd replied to Vincent Cuenca's discussion hardtail bridge for 6-string license plate guitar
"Or use a wrap bridge/tailpiece that will be up off the surface."
6 hours ago
A.D.EKER posted a video

Turkey in the Straw BCB - A. K. A.- A. D. Eker 2023 - 2024

a Old Day Americana Classic "Turkey in the Straw,Turkey in the Hay" ,there are some differend translation and versions from this Americana Classic, this i...
6 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

BCB Season Greetings 2023 2024

"Oke Kale ! its getting closer Kroatia wont stop , and in Gaza  the Jews keep demolishing a…"
6 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

BCB Season Greetings 2023 2024

"Hia Keith ! thanks for the listen ! appriciated !"
6 hours ago

Events

Music

© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->