Never used one, but they look good despite being cheap and quick.  Looks to me like the string would break easily over the sharp edge of the hole.  Is this a problem?  Thanks.

Views: 619

Reply to This

Replies to This Discussion

Never does for me. I think that is because there is no break angle so the strings really don't contact the edges much, at least the way I've mounted them.
In the good old days all the major guitar companys use this type of tail pieces and some still do. I can't recall ,of the several hundreds of guitars that I have sold and seen that was much of an issue.

Cheers
Bob:)
If you're worried about possible string breakage on sharp edges then it's not difficult to take the edge off a little. I've made some guitars with tailpieces made of plain brass sheet with holes drilled in, which initially gave me similar concerns. I have a couple of things I do to reduce the risk of string wear/breakage and it's possible you could do something similar.

What I do is de-burr the holes with a drill and then give them some brief attention with medium to fine abrasive paper.
By de-burring I mean I take an oversize drill bit (eg. for a 2mm hole I'd use maybe an 8mm drill) and, just holding it my hand, twist it lightly against the hole to shave off any burrs that have been thrown up by the initial drilling.
With the abrasive paper I take small pieces and roll them into cones, which I can push into the hole and twist so that they work on the edge.

Maybe I'm being over cautious. I've never had a string break at it's tail end, but I don't know if that's because of my precautions or becauae it's unlikely in any case. It's possible the relative hardness of the metals of the strings and tailpiece might make a big difference. If you're using strings made from a hard steel and you've got a tailpiece made from a softer metal, such as brass, then maybe it's more likely the strings will wear away the tailpiece than the tailpiece will wear through the strings.

What sort of hinges do you have?
been playing this one for bout 3 years, no problem with the hinge breaking the strings

like diane says, not much break angle on the strings
I've had good success with hinge tail pieces. Never a broken string in that area. Remember to keep the string outlet on the tail piece LOWER than the saddle part of the bridge.
Yup , I put mine string hole right down close to the top of the box and if I get any buzz, I just put a strip of leather or mouse pad just under the string next to the edge of box too.

Uncle John said:
I've had good success with hinge tail pieces. Never a broken string in that area. Remember to keep the string outlet on the tail piece LOWER than the saddle part of the bridge.
Mark aka. Junk Box Instruments said:
If you're worried about possible string breakage on sharp edges then it's not difficult to take the edge off a little. I've made some guitars with tailpieces made of plain brass sheet with holes drilled in, which initially gave me similar concerns. I have a couple of things I do to reduce the risk of string wear/breakage and it's possible you could do something similar.

What I do is de-burr the holes with a drill and then give them some brief attention with medium to fine abrasive paper.
By de-burring I mean I take an oversize drill bit (eg. for a 2mm hole I'd use maybe an 8mm drill) and, just holding it my hand, twist it lightly against the hole to shave off any burrs that have been thrown up by the initial drilling. I have no shortage of rotary burrs and machinists' countersinks, 60 degree point, any of which
should do the job nicely.


With the abrasive paper I take small pieces and roll them into cones, which I can push into the hole and twist so that they work on the edge.

Maybe I'm being over cautious. I've never had a string break at it's tail end, but I don't know if that's because of my precautions or becauae it's unlikely in any case. It's possible the relative hardness of the metals of the strings and tailpiece might make a big difference. If you're using strings made from a hard steel and you've got a tailpiece made from a softer metal, such as brass, then maybe it's more likely the strings will wear away the tailpiece than the tailpiece will wear through the strings.

What sort of hinges do you have?

Ives brass decorative hinges from HD, fleur-de-lis shape, part #C9072B3. Also have some similar
larger decorative hinges pulled off discarded cabinets, unknown mfr and part #.
Thanks, all, you've been phenomenally helpful.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Uncle Toad Feb 25. 5 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

HELP !! IN VERMONT.

Started by Ranblin' Dan Stevens in Other stuff - off topic, fun stuff, whatever. Last reply by Patrick Kelly Jan 21. 7 Replies

Latest Activity

Aaron Green posted a status
"@Uncle John, I love that Idea! Lol, I'm taking it!"
25 minutes ago
Sam T is now a member of Cigar Box Nation
1 hour ago
Uncle John commented on A.D.EKER's video
Thumbnail

Waiting at the Station BCB 2024

"Got that photo Andries,  Thanks, I like it a lot.   Cool on the Triumph from your…"
2 hours ago
A.D.EKER commented on Southern Ray's photo
Thumbnail

Getting there...

"Nice and smooth Ray ! Two string chugger ?"
2 hours ago
A.D.EKER commented on Poorness Studios's video
Thumbnail

CD Player (an original rap about my CD collection)

"Some things keep coming Back ! (don't no if the CD does)  i have some ,but mainly…"
2 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Waiting at the Station BCB 2024

"Thanks Kale ! yep its on my Old TRIUMPH  i inherrited it from my past away sister, somehow…"
3 hours ago
A.D.EKER commented on A.D.EKER's video
3 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Waiting at the Station BCB 2024

"Thanks a lot keith ! most appreciated !"
3 hours ago
A.D.EKER left a comment for Uncle John
3 hours ago
Robert Vance Jr. liked Robert Vance Jr.'s profile
7 hours ago
Robert Vance Jr. liked Aaron Green's photo
8 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

First Chugger

" Thank you Doug. You certainly know your way around the chuggers and make them sing. I've…"
12 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->