Howdy! This is my first post here on The Nation, and I have an amp question.

I scored a VOX VT15, 15 watt amp in partial exchange for some work I'm doing for an aquaintence, and there's a problem with the potentiometer marked MASTER on the top panel. If I adjust the knob, I get loud static out of the speaker, and sometimes the volume cuts out all together. I have to kind of play with it to keep the volume up on it to the point that you can hear anything out of it.Other than that one annoyance, it sounds great. I think a CGB will sound great through it - and you can't beat free for a price.

My question is, do you think a bit of contact cleaner sprayed down into the potentiometer will do the trick, or do I need to replace that potentiometer?

Thanks in advance for your help.

Views: 361

Reply to This

Replies to This Discussion

Mark,

Try the contact cleaner first, then check for a simple loose connection. Be very very careful if you decide to open it up; there are literally killing voltages inside. If you don't trust yourself, take it to an amp tech.

Thanks very much for the reply. I know my limitations when it comes to anything electronic, so the replacement will be done by a tech if I need to go that route. Just wondered if anyone had had any success with the contact cleaner before I shell out the money to have it replaced.

I always spray a little contact cleaner on my pots every once in awhile; it gets pretty dusty at times where I live. The contact cleaner should remove the crackle; after spraying it, work the knob back and forth a few times. If that doesn't work, then the behavior sounds like a simple loose connection. People give stuff away all the time, thinking it's broken; I just fixed a guitar input jack that had a broken input lead for a kid and father who don't know how to do simple soldering, and were prepared to pay some serious money to the local techs. Was a 20 minute job, and the kid and father both went away happy.

Just to update and finish out the story here, the contact cleaner worked like a charm. I pulled the back off the amp, pulled the amp out of the cabinet, and found the board the pots were soldered to. I then removed the screws that held that board onto the main amp board. I gave all of the pots a good sluicing out with the contact cleaner while turning them back and forth to knock any gunk loose while the cleaner was being sprayed. I put it all back together, plugged it in, plugged in the guitar, and whammo - it sounds great.

I did discover that the cabinet is about shot. It's made of particle board and it's coming apart in a few areas - especially around the speaker opening and along the back where the back panel screws onto it. I think I'll be making a new cabinet for it down the road. Who knows - if I find a neat old soap box or antique radio that doesn't work, I might swap the internals out into that.

Thanks for the help!

Mark,

Thanks for coming back with, as Paul Harvey used to say, " the rest of the story." if you do decide to re-box the guts of the amp, try birch plywood. Many of the top amps use it, and it isn't all that expensive. The expense comes from finger jointing it. You could butt join it, with some decent wood or carpenter's glue like Titebond, and you might be amazed at how different the speaker and the entire amp sound. Particle board and MDF soak up sound.

I've often been able to extend the life of crumbling particle board by "painting" the weak crumbling areas with a good coat of carpenters glue (Titebond).

 

When dry it completely seals and strengthens the effected area. Paint it into worn out screw holes as well and it will give enough new surface so the screws will have something to grip.

 

Like your contact cleaner ... it might be worth a try.

Thanks guys.

I have a good woodworking background in cabinetry, so making a new amp cabinet isn't a problem. I can't tell you how many sheets of birch plywood I've cut into cabinet parts. It looks like the speaker itself is screwed to a piece of 1/4" luan plywood, but I'll most likely switch over to birch for that too. Still up in the air about whether to build a new cabinet or keep my eyes open for something that can be made into one.

Film at 11...

Mark,

Ahhhh, cabinetry skills. So, no prob finger jointing it, then.

If you do go birch, then you definitely want the speaker baffle (technical term for the piece of wood the speaker is screwed to) made out of the same material. You want the speaker baffle to be relatively thin ( 1/4" or even less) compared to the cab frame. I think if you just built a new cab, without changing anything else, you'd find the amp sounds completely different, and waaaay better than it currently does. And that's without doing a speaker upgrade.

For the cabinet carcass itself I'll probably go with biscuits rather than finger joints. The current cabinet is covered in black vinyl, and I like that look. I may change the color to brown (I have some handy) but nothing is written in stone. Black vinyl is easy to find cheap. I've decided that this will be for using, not setting on a shelf and looking at, so I'm not looking for a showpiece.

I'll grab some 1/4" when I get the 3/4" cabinet material and cut a new baffle for the speaker. Then again, if they have maple at a decent price, I might go that route and skip the vinyl covering all together.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on Dar Stellabotta's video
Thumbnail

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

"i See Your ready to Blow away the GRAND STADIUM ! tree strings more of DAR DELIGHT !! Shine Girl !…"
6 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you for the kind comments Doug! Glad you liked the Picture !"
6 hours ago
BrianQ. commented on Dar Stellabotta's video
10 hours ago
BrianQ. liked Dar Stellabotta's video
10 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
12 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
13 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
14 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
14 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
16 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
16 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
17 hours ago
A.D.EKER commented on Ricky D's photo
17 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->