A while back I posted on the comments about this nasty little op amp that I built. It has 2 IM386N1 chips and it's a 2 stage amp. It was inspired by the Ruby amp.

Here's a schematic if anyone is interested in building one.

Views: 897

Replies to This Discussion

It took a couple of tries to lay it out good and clear. There is software out there to make layouts, but drawing it is cheaper. LOL

I didn't make it clear enough for the input caps. they are on a toggle to switch for Guitar mode .047cap or bass/bass boost mode .1 cap. The cap wires go to both Volume pots so your choice goes to both chips.

And you are seeing the back side of the pots in the schematic.

If you set Volume 1&2 at 10 and Gain 1&2 at 7, you'll get a Fender Champ sound. Up Gain 2 to 10 and it'll be more like a Fender Tweed. Turn the Gains to 10 and the Volumes down for gobs of nasty distortion.

 Would it be possible to get photos?

 I have done NO electronics work at all but scored a nice box today I can get two 6" speakers in.

Would love to try it but photos would definitely help.

This one looks good as I play bass and have a CBB I want it for.

I'm having a little trouble with the output circuit on this right now. It needs capacitors on both the positive and negative sides to the speaker, but till I get a new speaker that can handle the decibels that the extra gain adds I won't know the right value caps to use.

If your going to use Bass a lot with the amp, you'll want a speaker/speakers that are rated for Bass use. Regular guitar speakers aren't voiced for Bass, but Bass speakers can be used for Bass or Guitar.This is a pic of the guts of a Head that I made for myself that didn't have the output circuit caps. It worked, but had a little hum in the output. The right caps will get rid of the hum and increase the output volume. I should find out what is needed in 2 to 3 weeks.

Electronics have 5 units of measurement: Volts-DC or AC, Amps-what it takes to push current through the circuit AKA resistance, Watts-measure of used current, Ohms-measurement of operational level of current and Decibels-level of sound that isproduced/heard.

Volume/loudness is measured in decibels and every speaker has a output level that is measured in wattage and decibels. Wattage is electrical and decibels is what you hear.

Even though this little amp has low output wattage, the output decibels are high because it's a bridged amp.

The speaker I have is a vintage speaker that works and sounds good under normal use and a decent amount of decibels. It'll work fine for a single chip amp, but this dual chip/bridged amp puts out more than this old speaker can handle. So that's why I need to order a new speaker and when it get here I'll be a happy camper.

Working on getting a video set up so I can demo this Badboy.

Electronics can be confusing, but once you get your head in the door it all starts to make sense.

 Thanks for the pic. Watched some vids too last night. Seems fairly simple but always daunting taking on that first project.

 I was just going to use speakers from an old ghetto blaster that's been in the basement for years.

 My bass is very short scale and adg strings. Either way I have some gits too :)

(I have bass amps, but playing on the street with a homemade one would be cool)

 thnx again

Those speakers won't last long with a guitar or bass, but subwoofers from a car stereo or home surround sound system will. Most of them are rated a 4ohm, but the 386 chips are rated at 6ohm to 8 ohm. If you wire 2 of them in series, you'll be fine.

This is actually the stereo I have, funny I just came across it looking for speakers on ebay.

 It's dual cone with bass boost???

http://www.ebay.com/itm/SONY-CD-RADIO-INTEGRAL-DUAL-CONE-SPEAKER-SY...

Do you think 2 of these would work well? Cheapest I can find, don't want to spend much :D

Also looking at this for an amp

http://www.ebay.com/itm/121910650981

 Thanks Wayfinder,

 I'm going to start a thread on this project and try to piece something together :D

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources


Discussion Forum

LM386 Amp w/ Switchable Clean Channel

Started by BrianQ.. Last reply by BrianQ. May 28, 2021. 1 Reply

Simple 1st Timer CBG Amp

Started by BrianQ.. Last reply by BrianQ. Sep 28, 2020. 25 Replies

Matching Speakers to LM386

Started by Southern Ray. Last reply by Southern Ray Aug 6, 2020. 11 Replies

Suggestions wanted for easy amp build

Started by Southern Ray. Last reply by Southern Ray Jun 16, 2020. 11 Replies

Ruby Amp

Started by BrianQ.. Last reply by Southern Ray May 17, 2020. 27 Replies

Low-Z pickup and components values

Started by Southern Ray. Last reply by Southern Ray May 13, 2020. 6 Replies

Oops

Started by Southern Ray. Last reply by Southern Ray May 3, 2020. 12 Replies

DIY Spring Reverb

Started by Kevin Keating. Last reply by Paul Craig Oct 17, 2019. 4 Replies

TDA2030A Amp

Started by Bama Hound. Last reply by Gary Stenzel Jul 23, 2017. 14 Replies

Home Brew Champ Tube Amp

Started by Scott aka Farmer Ted. Last reply by Paul Craig Feb 6, 2017. 3 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Jan 27, 2017. 29 Replies

5 Watt Amp Kit (DIY Case)

Started by Walter Haapapuro. Last reply by Gene Jones Dec 7, 2016. 46 Replies

DIY reverb behold - I found this online

Started by Danny B.. Last reply by Paul Craig Nov 2, 2016. 3 Replies

Bass Cabinet project

Started by Murdoc_420. Last reply by Murdoc_420 Jul 16, 2016. 34 Replies

Kalamazoo Model 1 Deluxe

Started by Scott aka Farmer Ted. Last reply by Rick Alexander Jun 20, 2016. 12 Replies

LM386 amp and other stuff

Started by Denis U. Last reply by Denis U May 29, 2016. 19 Replies

Combo Amp Build

Started by Paul Craig. Last reply by Paul Craig May 27, 2016. 113 Replies

Latest Activity

Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Pharoah Pharoah: 2-String Chugger Cigar Box Guitar

"Thanks Kale! The teens really liked doing this one and the classic Louis Louis rhythmic chord…"
9 hours ago
Taffy Evans replied to Patrick Kelly's discussion Proof is in the Tuner
"Hi Patrick, thanks for the update. Yes, you are correct in saying that small tuning imperfections…"
13 hours ago
Doug Thorsvik commented on Rich's photo
Thumbnail

3 guys CBG back

"I’m on to your album tricks Rich! ;)"
13 hours ago
Doug Thorsvik commented on Rich's photo
Thumbnail

3 guys CBG Front

"Fantastic artwork as always Rich!"
13 hours ago
Doug Thorsvik commented on Rich's photo
Thumbnail

3 guys CBG head stock Front

"Signature headstock! Lookin’ good Rich."
13 hours ago
AGP # liked Randy S. Bretz's photo
13 hours ago
AGP # liked Randy S. Bretz's photo
13 hours ago
AGP # liked Randy S. Bretz's photo
13 hours ago
AGP # liked Doug Thorsvik's video
13 hours ago
AGP # commented on Danny Gordon's video
Thumbnail

All My Loving and Yellow Submarine on the Lap harp

"That's a  "Pretty Cool Instrument" Danny, did you build that one yourself…"
13 hours ago
AGP # liked Danny Gordon's video
13 hours ago
BrianQ. left a comment for Pete Asselin
"Here’s a step by step of how to build a simple 25” scale…"
14 hours ago

Music

© 2022   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->