I'm trying to drill 90 degree 14mm hole .
My hammer drill without hammering is too fast.  Cutting is not clean and wood splits. Maybe i'm doing something wrong.
I have  drill guide for it


I also have drill stand.
What I don't have is drill guid for my cordless drill.
As european I cant buy wolfcraft older model or any thing like this

I only have hand tools, dremel and drills.

Drill bit is wood twist bit.

One problem is that hole is near the edge.

Maybe I need to drill more away the edge and then cut the plywood.

I don't need big piece of wood. Also wondering how strong are aluminum tubes.

Views: 2955

Reply to This

Replies to This Discussion

 

I use a drill guide like yours with my big Bosch hammer drill , with the hammer off of course , works a treat every time , even used on my last build to put in the 2mm side dots . less pressure on the drill bit and make sure it's well supported underneath .

For a clean side wall, try a brad bit or a forstner bit - pretty cheap at HF

Someones recommended:

If the wood is splitting / tearing up on the entry and exit of the hole, it's helpful to clamp some "sacrificial" scrap wood on top / below your working piece--the scrap wood takes the damage instead.

What kind of drill bit are you using? Spade or auger bits will just rough out the hole. They eat up the wood so you can drill the hole quick. You need the regular twist or forstner tip for smooth finish holes.

Very slow feedrate is important

Hi Jantan,

Forstner bits seem to be the best for cutting smallish holes. I use a 1 inch (25.4mm) forstner bit to cut sound holes on my sound boxes. As you mentioned, adding a sacrificial board to the underside of your work piece will help prevent breakout, so I always put another scrap board under the one I'm drilling out to prevent breakout. Preventing breakout on a sound board that is actually the lid of your cigar box is a bit tricky, but usually a block of wood wedged inside the cigar box so it doesn't move around works pretty well to back up the sound board when drilling thru it. When I drill thin pieces like sound boards, I give the drill short bursts of power so the drill doesn't come up to full speed, but still turns well enough to cut thru the wood. I just have a single speed electric hand drill (no drill press or base attachment to steady my drill).

As far as Aluminum tubing, I don't really know. The only aluminum I uses is the aluminum from aluminum meter sticks, using small pieces to build simple tail pieces. The metal seems brittle compared to say copper or brass.

Good luck...

-Rand.

you need a saw drill bit, place a block of wood beneath the lid you are drilling the hole into, the bit has a built in pilot to make it easy.  you'll have to prise the ring of waste wood from the bit barrel between each cutting but it works very neatly! (-:  will all fit into a bench drill stand too.

 

This type of drill will not tear the surface of the timber,

Drill through from one side until the centre point just breaks through,turn over and drill from the underside

I have 14mm twist drill like in picture. I know that this is best. I also know that forstner bits are very good.

Forstner bits problem is price and where to get it in estonia. Too new in estonia.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->