Hi,

Building my first CB uke and when I strung it the the action lifts signifcantly.

The neck is bolted and glued and is firm as are the nut and bridge but the neck lifts under tension.

The sound board is the bottom of the box which was the deeper portion and I haven't glued the lid yet which may help brace it but I don't want to do this if I will need to fit bracings.

I have a piece glued beneath the bridge location just a little larger than the bridge itself and square batons all round the edge inside the box.

Maybe there's a thread already on this subject - I can't be the first!

Any help welcome!

Views: 663

Reply to This

Replies to This Discussion

How is the neck connected to the body? It sounds like the box is flexing where it's connected to the neck..got a picture?

Like CBJ says, maybe the lid is "caving in" a bit, which will also make the string height increase.

4 string uke...unlikely to be the neck bending unless you've tightened the strings waaaay too much.

CBJ most likely has the right of it and it's a simple fix, just cut a couple of gussets from fretboard scrap and glue one on either side of the neck location inside the box.

String pressure on a pinned bridge causes the sound board to bend up raising the action, profanity and bracing is the solution to that issue. I'm sure you've seen old acoustic guitars with that problem it's a PITA to correct.

A guitar with a tailpiece exerts downward string pressure to the sound board and can lower the action too much. The solutions are to make a taller bridge to compensate or add bracing to the sound board.

Thanks guys - checked the problem more carefully and it seems the movement is at the neck joint to the box. I just had one bolt through a block on the inside into the neck but another screw and some glue should sort it.

I didn't want to glue anything till I was sure.

Will check the bridge/saddle when I get the neck sorted.

It's my first attempt and it's amazing what you learn when you try doing it yourself. And very satisfying to hear a real note out of it!

Cheers all

Hope that works out for you.

Play us tune on it when it's done. :D

One bolt and one screw now and the action is way down - great result guys, thanks.

Might let you hear it when I learn to play - that's the next project :-)

It sounds like you have the box sandwiched between the neck and a block on the inside. If that's the case the box is probably twisting and it will likely happen again with some time. It's a good idea to have the neck run all the way through the box or some type of bracing that runs the length of the box with a solid way to attach the neck to the box and bracing. It's amazing how many things we learn in the first couple of builds, you'll only get better with each build. Keep on building!

As always, Bruce sums up exactly my thinking as I'm reading this thread.

Sounds like the top - end panel joint is flexing.  Reinforce with a glue block.

I tend to use a through neck and a tail piece which will prevent this problem, but the lack of a back will certainly let things flex a lot. The added backing block you have already added should also help keep you out of trouble;-)

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

Look what I picked up

Started by John B Treutlein in Performances, How to Play, Lessons, Concerts. Last reply by John B Treutlein Jul 2. 12 Replies

Blog Posts

Spammer Alert, Beware!!!

Posted by BrianQ. on September 11, 2023 at 6:30am 0 Comments

Montana Mandoline

Posted by CaptnCatfish on August 27, 2023 at 6:26am 3 Comments

Banjo 2

Posted by Ian Boyd on August 26, 2023 at 10:58pm 1 Comment

Latest Activity

David Woodman posted photos
4 hours ago
David Woodman posted photos
4 hours ago
Keith Rearick liked CaptnCatfish's video
11 hours ago
BrianQ. commented on CaptnCatfish's video
Thumbnail

6. Smokin' Guitars 2023 - Cigarboxguitar Festival Germany - Pleutersbach

"Thanx Captn. it’s been ages since someone posted a festival video, much appreciated!!"
12 hours ago
BrianQ. liked CaptnCatfish's video
13 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Stand By Me: 2-String Chugger License Plate Cigar Box Guitar

"Thanks Alan! Being a Beatles fan, I had to check out the John Lennon cover and was not disappointed."
14 hours ago
Rich commented on Ghostbuttons's photo
Thumbnail

Bicolor

"This looks good, Warren. I like the off set neck placement."
15 hours ago
Rich liked Ghostbuttons's photo
15 hours ago
Uncle John commented on Matthew Borczon's video
Thumbnail

lovesome valley

"Yup.  Lovin' it."
17 hours ago
Uncle John commented on A.D.EKER's video
Thumbnail

Baby Please don't Go BCB A.D. Eker 2023

"Excellent!  I always like this song.  Good version!  Nice guitar work, Andries!"
17 hours ago
Uncle John commented on Poorness Studios's video
17 hours ago
Uncle John commented on CaptnCatfish's video
17 hours ago

Events

Music

© 2023   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->