This has nothing to do with a CBG, but the situation I was dealing with and how I overcame it could be helpful to someone as far as building technique/solutions are concerned.

I acquired a set neck body for a SG type guitar on FB Marketplace for a good deal, finding a neck for it wasn't easy.
I had also acquired a Gibson scale bolt on neck for a cheap amount.
So I thought about adapting the bolt on neck to the set neck body. I was working on a set-neck SG kit and compared the 2 and decided that I'd make a "spacer" to glue in the neck pocket to bolt the neck onto or glue the neck to or both!

The spacer would have to have a degree cut of 4 degrees to give the neck the right tilt, but it would have to have the neck at the right height and the part in the neck pickup cavity would need to remain a certain thickness without interferring with the neck pickup height adjustment.

Using the kit set-neck to get all my adjustments and checking the bolt on neck measurements, then subtracting the last from the first, I was able to get the right measurements for the needed spacer. I made 4 spacers before I got it all correct and cut right. I used some Red Oak I had in my shop for strength and had to orientate the wood to ensure that I wouldn't be gluing or bolting into end grain.

The spacer at the body pickup cavity is 10mm thick, 12mm thick at the end of the neck past the 22nd fret and 5mm at the 17th fret where the spacer ends.
Total length of spacer is 115mm
Width is 57mm to fit the neck cavity tightly and happened to be right with the neck width.

I'll be attaching the spacer first and then the neck being careful to get it in it's right scale position, making sure it's high enough for strings to be in plane with the bridge and making sure the neck is straight so outer strings with have good spacing on the fretboard without dropping off.

Views: 533

Attachments:

Replies to This Discussion

This guitar has been a PITA! I've had a bunch of issues, but then I got some more. While pressing in the bridge post bushings,the body cracked from the bridge pickup cavity to the back end of the body. It's a thin crack, so fixing it isn't needed yet. I decided to wait and see if it opens up more before dealing with it.
I got it all together and put a couple strings on it and the neck angle is too much(4degrees). It looked right when I checked it with a straight edge. Looked at my straight edge and found that it had a slight bow in it. Did my Yosimite Sam impression. LOL
Now I have to route down to 3 degrees and recheck. Then more if needed.

I was building 2 guitars at once and both gave me trouble, but I finished one of them and I'll get this one finished too.

Done with this one for know. It needs touch up for the body paint, but I'm waiting to see if the body crack starts opening or not before painting. Either way it'll get fixed eventually.
The final degree for the neck on this ended up at 3 degrees. With a guitar that requires a angled neck, it's hard to say what degree it will need. I have 3 SG's now and they all have a different neck angle. One is 4, one is 3 and the other is 3.5. The best way to figure it out is by putting it together loosely clamped, adding the 2 outer strings and adjusting til it looks right. Then take measurements at the neck joint for the proper shim/angle.
This pickup combination has become my favorite: A5 P90 in the bridge and real A2 Firebird in the neck = Glorious Tone.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Cutting deep boxes in half

Started by Justin Stanchfield. Last reply by Taffy Evans Mar 20. 9 Replies

Attention 1st time builders!

Started by BrianQ.. Last reply by MadGomer Feb 27. 2 Replies

Brickhouse CBG Wiring

Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply

Fretless fret markers

Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies

canjo building and tuning

Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies

Minimum tools needed

Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies

High G problem

Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies

Doubling the high string

Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies

Aluminum License Plate

Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies

C. B. Gifty three string fretless kits.

Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies

Frettin' and stainin'

Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies

Bolt on neck to a set neck body?

Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies

Locations

Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies

Help please re Bento Box Uke "nut"

Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies

Clarification on pick ups

Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies

Licence plate cbg

Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies

Builder's Tips

Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies

Getting there but needing advice/help please.

Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies

Tres Cubano Build

Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies

CB Gitty Country Roads Banjo kit

Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies

Latest Activity

A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
13 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
13 hours ago
Kent Thurston updated their profile
13 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
14 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
14 hours ago
Poorness Studios liked A.D.EKER's video
16 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
16 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
19 hours ago
A.D.EKER commented on A.D.EKER's video
22 hours ago
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
22 hours ago
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday
Papa D commented on Papa D's photo
Thumbnail

american1 Sun Glo

"Thanx AGP & Doug..  4 more coming soon"
yesterday

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->