Hello all. I want to put fretboard on my cbg. My question is that if I put a 1/4 inch fret board on a 3/4 inch neck that makes the neck pretty beefy at one inch. Am I missing something about fret boards or is there a way to deal with thickness

Views: 310

Reply to This

Replies to This Discussion

It's the way it's usually done. A 6 string guitar is close to 1" after putting it together, but then the backside is carved and the fretboard gets a radius. The first fret area will usually be rounded and the higher end will usually be flater to enhance hand comfort/control and ease of play.

A 4 string or 3 string has a neck that's not as wide. That gives easy finger access all the way over the fretboard. Some prefer a large mass for the entire neck for comfort/control on these necks. It just comes down to what is more comfortable for you and gives you the control you need.

I have medium length and width fingers and find that the 3/4" necks with 1/4" work well for me. I usually carve a V shape to the back of the necks and use a radius on the fretboard because I'm used to that from playing 6string guitars for many years. Some prefer a squarish neck with rounded edges.

One inch is "thick" for a neck at the nut end, but not down at the box end. Without a truss rod, the additional beef at the nut end may be warranted (or not depending on the string selection). Most players/builders keep it simple and just play with the neck at a constant thickness (1"). Since the neck is only 1 3/4" wide, it's not like trying to reach around a log.

There are several things you can do regarding the neck profile, depending on the wood being used and how much work you want to put into it.

It is possible to taper the neck from nut to box and round the neck contour.

If you have access to a table saw or a band saw a taper jig is pretty easy to build so you get consistent results.

Another thing that you can do is use a fret board that is a bit under 1/4" thick. There is a practical limit to how thin you can make it based on the frets you use, but once it is glued to the neck, it will be strong and rigid.

A final thing is to taper the neck from the nut to the box in the up/down direction. This is pretty much what a traditional acoustic guitar has. My Gretsch acoustic is only 9/16" thick at the nut (including the fret board).

While there are many things you "could" do. I would suggest that you begin with a normal 1 3/4" wide neck and a 1/4" fret board. Fully round the underside of the neck. Make it nice and smooth the play it for a while and see if an ultra-thin neck is really worth the additional work.

Good luck

Keep us posted

Tom's reply shows how people on this page are willing to share their knowledge.

If it is a 3 string and both woods are hardwood, 3/4" is plenty thick in total.  Built and seen plenty of 3 stringers in oak or maple with no fretboard and no issues.  Poplar and other soft wood is another story.  Whether it is worth the effort to thin it down is the next question!  You can always build it, then round it or thin it more if you don't like it, but it is not so easy to add some back.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->