I made a git for the Plumbers Challenge and decided to post the build here.

Awhile back, I had thought about building a guitar that was made out of PVC for a "Tubulum" acoustic effect. So the build challenge was the excuse I needed.

The body was made of schedule 40 PVC pipe and fittings. I used a 1 &1/4" piece over the 1" piece on the neck so that the fretboard would set evenly.

I used a electrical box cover for the control plate. I used a 500k pot for volume and a input jack. I had some left over tuners from other projects(CBGitty Tuners). 3 tuners for the 3 strings on the git, mounted in the ends of a 4-way fitting on the end of the neck. 1 tuner is used for a heavy string running along the back inside of the neck and acts as a trussrod, tighten to add relief and loosen to let the neck ramp some.

The Pickup is a hacked hand drill motor part. The coils from the motor have magnetized metal pole shoes holding wire coils that are wired in series. Thought to myself that this might work as a humbucking pickup, it does. It was a little weak, so I added a couple round ceramic magnets that also came from the non-working drill(had a bad armature). The fretboard and strings run through the "Pickup"(one coil on top and one coil below) and the pickup slides along the through fretboard towards the neck for bass tones and towards the bridge for treble tones. Similar to the old "Monkey On A Stick Pickups".

It does well for fretless guitar or slide and has good acoustic volume and tone. The pickup works and bucks the hum, but it isn't very loud(suitable for bedroom volumes). 

Views: 484

Replies to This Discussion

Here's a couple picks of the body. 10" wide and 15" long.

Body with neck attached.

Putting in the tuners was a challenge. Had to drill a hole for the post and then add washers for spacing. Had to wedge pieces of wood under the tuner to hold it in and around the tuner to hold it steady in place.

Pic of tuners and rear truss string and tuner.

Pics of the yardstick fretboard and pickup.

FANTASTIC!!!!!!!!!!!! That all I got. ( mind is blown ) love to hear it, smiley face

Nicely done!

Thanks

plumb crazy ;-)

Well done Paul, very cool!

Thanks

Thanks LOL

Thanks.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Cutting deep boxes in half

Started by Justin Stanchfield. Last reply by Taffy Evans Mar 20. 9 Replies

Attention 1st time builders!

Started by BrianQ.. Last reply by MadGomer Feb 27. 2 Replies

Brickhouse CBG Wiring

Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply

Fretless fret markers

Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies

canjo building and tuning

Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies

Minimum tools needed

Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies

High G problem

Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies

Doubling the high string

Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies

Aluminum License Plate

Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies

C. B. Gifty three string fretless kits.

Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies

Frettin' and stainin'

Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies

Bolt on neck to a set neck body?

Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies

Locations

Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies

Help please re Bento Box Uke "nut"

Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies

Clarification on pick ups

Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies

Licence plate cbg

Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies

Builder's Tips

Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies

Getting there but needing advice/help please.

Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies

Tres Cubano Build

Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies

CB Gitty Country Roads Banjo kit

Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies

Latest Activity

BrianQ. commented on Dar Stellabotta's video
3 hours ago
BrianQ. liked Dar Stellabotta's video
3 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
5 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
5 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
7 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
7 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
8 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
9 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
9 hours ago
A.D.EKER commented on Ricky D's photo
9 hours ago
A.D.EKER commented on A.D.EKER's video
9 hours ago
Keith Rearick liked Doug Thorsvik's video
13 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->